SignalFire Wireless I/O Module Mini Interface Manual Download | Manualshive

Page: 6 / 10

background image

Rev 1.5

SignalFire Telemetry

6

Modes of Operation

The Wireless I/O Module Mini can be run in two software settable “system modes”:

Node

,

and

Point-to-Point

. The ToolKit has a Radio Mode dropdown that can be set to either

Node or Gateway. For the WIOM Minis to operate in Node mode, all WIOM Minis on the
network must be set to Node and they will communicate with a SignalFire Gateway. For Point-to-
Point, set one WIOM Mini to Gateway and one WIOM Mini to Node, on a network that has no other
devices.

Node Mode

In Node mode, the WIOM Mini will send its analog and digital inputs/outputs to the Gateway. All IO
and then be read/set from a PLC via Modbus.

Node Mode. The Gateway reads all inputs from all nodes, and can control any output of any node as commanded by a PLC

«
...
4
5
6
7
8
...
»

Summary of Contents for Wireless I/O Module Mini











Reviews:

No comments

Related manuals for Wireless I/O Module Mini

Brand: N-Com Pages: 2

Brand: Nacon Pages: 12

Brand: RAPIBREW Pages: 16

Brand: S.E.M. Pages: 6

Brand: hotset Pages: 2

Brand: M-E Pages: 4

Brand: Eaton Pages: 7

StorageWorks DS-BA35X-MN

Brand: Digital Equipment Pages: 2

Brand: D-TACQ Solutions Pages: 8

Brand: Aiphone Pages: 20

Brand: Telefunken Pages: 41

ProcessLogix 1757-SRM

Brand: Allen-Bradley Pages: 36

Brand: Gage Pages: 36

Brand: AXEM Technology Pages: 31

Brand: Feig Electronic Pages: 35

Brand: Aqua Creek Pages: 16

Brand: Vestil Pages: 6

Brand: Bouyer Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands