Signet SVMP2-8 Operation & Instruction Manual Download

Page: 6 / 6

Page 6 of 6

DocNo.DCP0001328 RnB 10/10/03 rev6

Output connections

Connecting a SVMP2-8 to the SigNET iX LS

Triggers of the SVMP2-8 are wired to whatever external

equipment will be used to trigger them (e.g. switched relay or fire interface).

Set Options to Non-monitored mode

Connecting a SVMP2-8 to the SS2n (Network station)

Set Options to Non-monitored mode

Only using one message channel.

If you are only using one channel of the SVMP2-8, connect audio+

and audio- of both message connectors in parallel. This will ensure that there is no audio fault reported on
the unused channel.

Specification

Storage capacity

2 messages, each of up to 120 seconds

Audio bandwidth

16kHz

Audio Output level

0dBm

Line Input sensitivity

0dBm (0.775V)

Power Supply Requirements

100mA @18-36 VDC, externally regulated.

Width

249mm

Height

41mm

Depth

159mm

(behind

front

panel)

Weight

2kg

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE

SigNET Amplification & Control

Tower Road, Glover Estate, Washington, Tyne & Wear, NE37 2SH.

Tel: +44 (0) 191 417 4551

Fax: +44 (0) 191 417 0634

Summary of Contents for SVMP2-8







Search results

Summary of Contents for SVMP2-8

Reviews:

Related manuals for SVMP2-8

Brands by name

Popular brands

Signet SVMP2-8, Operation & Instruction Manual

Search results

Summary of Contents for SVMP2-8

Reviews:

Related manuals for SVMP2-8

Brands by name

Popular brands