background image

13

SIIGView GUI Installation

The SIIGView Graphical User Interface (GUI) provides a

web-based, real time, local monitoring of your 

SATA

RAID 5/0 Bay Enclosure

.

1.

Place the driver installation CD into the CD-ROM

drive.  Auto-run should start the installation.  If not,

click 

Start

, then 

Run

.  Type 

D:\autorun

, then click

OK

. (Change 

D:

 to match your CD-ROM drive

letter).

2.

At the 

SIIGView

 window, click the 

SIIGView 

button.

3.

At the 

SIIGView 1.0 Setup

 window, click 

Next.

4.

Check 

I Agree to the terms ....

, click 

Next.

5.

Type a 

Name

 and 

Company

 (if desired), click 

Next.

6.

Accept the default folder, click 

Next

.

7.

At the 

Shorcut folder

, select the option that best fits

your needs, then click 

Next

.

8.

Click 

Next 

to proceed with the install.

9.

When prompted, click 

Finish

.  Close the 

SIIGView

install window.

10. Two shortcut icons will appear on the desktop after

software installation:

SIIGView Server

:  to launch SIIGView software

program.

SIIGView Monitor

:  to open the SIIGView

monitoring window.

SIIGView GUI

In order for SIIGView GUI to operate, the RAID box must

be connected to a  serial port on your system.  Please refer

to step #10 on page 8 for more information.

Summary of Contents for SC-000081-S1





















Reviews: