background image

19

Technical Support and Warranty

QUESTIONS?

  SIIG’s 

Online Support

 has answers!

Simply visit our website at 

www.siig.com

 and click on 

Support

.

Our online support database is updated daily with new drivers

and solutions.  Answers to your questions could be just a few clicks

away.  You can also submit questions online and one of our technical

support analysts will promptly respond.
This product comes with a 5-year manufacturer warranty.  Please see

SIIG website for more warranty details.  If you should happen to have

any problems with this product, follow the procedures below.
A)  If it is within the store's return policy period, please return the

product to the store where you purchased from.
B)  If your purchase has passed the store's return policy period, please

follow these steps to have the product repaired or replaced.

Step 1:

  Submit your RMA request.

Go to 

www.siig.com

, click 

Support

, then 

RMA

 to submit a

request to SIIG RMA.  If the product is determined to be

defective, an RMA

 

number

 

will be issued.  SIIG RMA department

can also be reached at (510)413-5333.

Step 2:

  After obtaining an RMA number, ship the product.

Properly pack the product for shipping.  All software, cable(s)
and any other accessories that came with the original package

must be included.

Clearly write your RMA number on the top of the returned
package.  SIIG will refuse to accept any shipping package, and

will not be responsible for a product returned without an

RMA number posted on the outside of the shipping carton.

You are responsible for the cost of shipping.  Ship the product
to the following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538

RMA #:

SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at

no cost to the customer.

Summary of Contents for SC-000081-S1





















Reviews: