background image

Operating manual

Twister II NA

Copyright Silca S.p.A. 2015

1

 GUIDE TO THE MANUAL 

 This manual has been produced to serve as a guide for users of the TWISTER II NA key-cutting machine. Read 
it carefully; it is essential if you wish to operate your machine safely and ef

fi

 ciently. 

Consultation

The contents of the manual are divided into sections relating to:

Transport and handling ...............................................................................................Ch. 1

Description of machine and safety devices ................................................................Ch. 2-3-4

Proper use of machine ...............................................................................................Ch. 5-6-7

Maintenance ...............................................................................................................Ch. 8-9-10

Technical terms

Common technical terms are used in this manual. To assist those with little experience of key cutting, below is an 
illustration of the terms used for the different parts of keys.

DIMPLE KEYS

keys with holes of different dimensions, 

depths, positions and shapes.

LASER (SIDEWINDER) TYPE KEY

 LASER is the name given to the 

special sidewinder milled keys.

Fig. 1

1) Head

5) Tip

2) Rim

6) Edge

3) Shoulder Stop

7) Cuts

4) Stem

 

Summary of Contents for Twister II NA

























Reviews: