Proposed
© 2005 Copyright Magnadyne Corp.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Models: 7921P, 7920P, 7919P Rev. C
S t e p 2
ON
☛
Disarm Security
System
The LED will be off and
the horn/ siren will emit 2
short beeps.
Insert the Valet Switch
Turn On Ignition
Push the Valet Switch:
4 Times if Using a Red Button Switch
8 Times if Using a Black Button Switch
(Represents 4 Times On / Off)
The LED will be on solid. The horn/ siren will emit 1 long
then 1 short beep) You are now in the “Dealer Remote
Feature Programming” mode.
S t e p 1
S t e p 3
S t e p 4
S t e p 5
Momentary Switch
Push On/Off
Toggle Switch
Push it On then
Push it again for Off
ON
OFF
Dealer Switch
(Red Button)
Consumer Switch
(Black Button)
O F F
Turn Off the Ignition
The LED will be off and the
horn / siren will emit 1 short
beep and 1 long beep. You are
now out of the feature
programming mode.
S t e p 6
When the Silencer
®
security system control module learns the
dealer transmitter operating code, a specific group of features
are automatically programmed to their default settings.
Enclosed, is a chart of the default settings for dealer transmitter
operation.
These default setting can only be changed by following the
enclosed procedures and using the special 5910P programming
transmitter (Shown Below).
To get into the “Dealer Remote Feature Programming” mode
repeat the following procedures:
#
Programmable Feature
Default Setting
1
Single/Dual Unlock Pulses
Single
2
Automatic Arm Door Locking
(See Note 1)
On
3
Chirp Status Indicator
(See Note 2)
On
4
Consumer Remote Feature Programming Modes for Automatic
Mode “P”
Arming of Alarm and Automatic Arming of Starter Disable.
( See Step 5 and Note 3 for Full Details)
Note: Pre-programming the “P and S” type auto arming modes is for use when the system is
put into consumer mode only. In dealer mode, auto arming is on without On/Off programming
and auto arm locking is on but can be programmed off as explained below.
#
Button Color
Changed Function
Confirmation
1
Black
Single or Dual Unlock Outputs
1 Beep = Single Unlock Pulse
2 Beeps = Dual Unlock Pulses
2
Blue
Dealer Mode Auto Arm Door Locking
1 Beep = Automatic Arm Door Locking On, Consumer Auto Arm is ON
Pre-Programmed Consumer Mode Auto Arm
2 Beeps = Automatic Arm Door Locking OFF, Consumer Auto Arm is ON
3 Beeps = Automatic Arm Door Locking On, Consumer Auto Arm is OFF
4 Beeps = Automatic Arm Door Locking OFF, Consumer Auto Arm is OFF
3
Red
Chirp Status Indicator On / Off
1 Beep = On, 2 Beeps = Off
4
** Black + Blue
Selects “P” or “S” Mode Operation
4 Beeps =
Mode “P”
(See 2A Consumer Programming)
Automatic Arming of Alarm is “Programmable”
and Automatic Arming of Starter Disable is
“Programmable” in Consumer Mode Only.
3 Beeps =
Mode “S”
(See 2B Consumer Programming)
Automatic Arming of Alarm is “Programmable”
in Consumer Mode. Automatic Arming of
Starter Disable is Always “On” and is
“Not Programmable” in Dealer or Consumer Mode.
Black
Button
Blue
Button
Red
Button
Use the 5910P transmitter and the chart below to adjust the features as
required. Press the button that controls the function you want to change and
listen for the chirp confirmation. You can repeatedly press the same colored
button and turn the same function on and off as many times as required until the
operation is correct. After all functions have been re-programmed to operate as
required go to step 6.
5910P Programming Transmitter
D E A L E R R E M O T E F E A T U R E P R O G R A M M I N G
☛
*
Note 2: When transmitter operation
is changed from a dealer
transmitter to a consumer
transmitter the horn/siren
and chirp indicator will return
to an “on” condition.
Note 1: When transmitter operation is changed from a
dealer transmitter to a consumer transmitter the
automatic arm locking feature will default to
“OFF”. This feature can be programmed on in the
customer mode by following the consumer feature
programming chart.
Note 3: When transmitter operation is changed from a
dealer transmitter to a consumer transmitter, the
automatic arming of alarm and automatic arming
of starter disable (Mode “S” or “P”) will remain as
programmed in the dealer transmitter mode. In
order to change Mode “S” or Mode “P” operation,
you have to re-code a dealer transmitter to the
unit and change the operation in the dealer
remote programmable feature mode.
** Note: The Black +Blue Buttons Change Automatic Alarm
Arming of Alarm and Automatic Arming of Starter Disable in
the Consumer Mode Only!
Default Dealer Mode Operation is Always: Automatic Arming of
Alarm “On”, Automatic Arming of Starter Disable “On” and
Automatic Door Locking “On”.
