Silicon Laboratories BRD4154A Reference Manual Download | Manualshive

Page: 7 / 17

background image

4.5 Inverted-F Antenna

The BRD4154A Radio Board includes an on-board printed Inverted-F Antenna tuned for the 2.4 GHz band. Due to the design restric-
tions of the Radio Board the input of the antenna and the output of the matching network can't be placed directly next to each other thus
a 50 Ohm transmission line was necessary to connect them. The resulting impedance and reflection measured at the output of the
matcing network are shown in the following figure. As it can be observed the impedance is close to 50 Ohm (the reflection is better than
-10 dB) for the entire 2.4 GHz band.

Figure 4.2. Impedance and Reflection of the Inverted-F Antenna of the BRD4154A

BRD4154A Reference Manual

RF Section

silabs.com

| Smart. Connected. Energy-friendly.

Rev. 1.0 | 6

«
...
5
6
7
8
9
...
»

Summary of Contents for BRD4154A


















Reviews:

No comments

Related manuals for BRD4154A

Brand: Tapeswitch Pages: 13

Brand: Acclaim Lighting Pages: 32

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: Tech 21 Pages: 2

Brand: Grosvenor Pages: 5

Brand: Wilo Pages: 128

Brand: ACTi Pages: 20

Brand: SOARNEX Pages: 14

Brand: Carel Pages: 36

Brand: OCL Pages: 2

SmartControl RS232

Brand: Savant Pages: 2

Brand: Atmel Pages: 27

Brand: Danfoss Pages: 8

AQ Logic Series

Brand: Bernard Controls Pages: 88

Brand: Jetter Pages: 28

Brand: VubIQ Pages: 17

Brand: Tekmar Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands