Silicon Laboratories C8051F005 User Manual Download

Page: 10 / 12

C 8 0 5 1 F 0 0 x / 0 1 x - D K

Rev. 0.6

OCUMENT

HANGE

IST

Revision 0.4 to Revision 0.5



Section 1, added USB Debug Adapter and USB Cable.



Section 2, changed name from "Hardware Setup" to "Hardware Setup using an EC2 Serial Adapter".



Section 2, added 2 Notes bullets.



Section 2, removed Note from bottom of page.



Added Section 3, "Hardware Setup using a USB Debug Adapter".



Section 5.4.2, changed step 2 to include new instructions.



Section 7, J4, changed "Serial Adapter" to "Debug Adapter".



Target Board DEBUG Interface Section, added USB Debug Adapter.



DEBUG Connector Pin Descriptions Table, changed pin 4 to C2D.



Changed "jumper" to "header".



EC2 Serial Adapter section, added EC2 to the section title, table title and figure title.



EC2 Serial Adapter section, changed "JTAG" to "DEBUG".



Added "USB Debug Adapter" section.

Revision 0.5 to Revision 0.6



Removed EC2 Serial Adapter from Kit Contents.



Removed Section 2. Hardware Setup using an EC2 Serial Adapter. See RS232 Serial Adapter (EC2) User's
Guide.



Removed Section 8. EC2 Serial Adapter. See RS232 Serial Adapter (EC2) User's Guide.



Removed Section 9. USB Debug Adapter. See USB Debug Adapter User's Guide.

Summary of Contents for C8051F005













Search results

Summary of Contents for C8051F005

Reviews:

Related manuals for C8051F005

Brands by name

Popular brands

Silicon Laboratories C8051F005, User Manual

Search results

Summary of Contents for C8051F005

Reviews:

Related manuals for C8051F005

Brands by name

Popular brands