Silicon Laboratories C8051F02 Series User Manual Download

Page: 5 / 12

AN172

Rev. 0.4

6. Target Board

The C8051F02x Development Kit includes a target board with a C8051F020 device pre-installed for evaluation and
preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping
using the target board. Refer to Figure 2 for the locations of the various I/O connectors.

Power connector (accepts input from 7 to 15 VDC unregulated power adapter)

Connects SW2 to P3.7 pin

Connects LED D3 to P1.6 pin

JTAG connector for Serial Adapter interface

DB-9 connector for UART0 RS232 interface

Jumper to connect UART0 TX (P0.0) to DB9

Jumper to connect UART0 RX (P0.1) to DB9

J11

Analog loopback connector

J12-J19

Port 0 - 7 connectors

J20

Analog I/O terminal block

J22

VREF connector

J23

VDD Monitor Disable

J24

96-pin Expansion I/O connector

C8051

F02X

ESET

J24

Pin 1

J11

Pin 2

J23

PWR

P1.6

J20

Pin 1

Pin 2

J22

Pin 1

Pin 2

Port 0

Port 2

Port 4

Port 7

Port 1

Port 3

Port 6

Port 5

Figure 2. C8051F020 Target Board

Summary of Contents for C8051F02 Series













Search results

Summary of Contents for C8051F02 Series

Reviews:

Related manuals for C8051F02 Series

Brands by name

Popular brands

Silicon Laboratories C8051F02 Series, User Manual

Search results

Summary of Contents for C8051F02 Series

Reviews:

Related manuals for C8051F02 Series

Brands by name

Popular brands