C8051F500DK
Rev. 0.1
11
8.4. Switches and LEDs
Two push-button switches are provided on the target board for each MCU. Switch RESET_A is connected to the
/RST pin of the C8051F500. Switch RESET_B is connected to the /RST pin of the C8051F502. Pressing
RESET_A puts the C8051F500 device into its hardware-reset state, and similarly for RESET_B and the
C8051F502 MCU. Switches P1.4_A and P1.4_B are connected to the MCU’s general purpose I/O (GPIO) pins
through headers. Pressing either one of these switches generates a logic low signal on the port pin. Remove the
shorting block from the header to disconnect these switches from the port pins. See Table 1 for the port pins and
headers corresponding to each switch.
Four LEDs are provided on the target board to serve as indicators. The red LED labeled PWR indicates presence
of power to the target board. The second red LED labeled COMM indicates if the CP2102 USB-to-UART bridge
(P5) is recognized by the PC. The green LED labeled with port pin name P1.3_A is connected to the C8051F500’s
(Side A) GPIO pin P1.3 through the header J19. Remove the shorting block from the header to disconnect the LED
from the port pin. Similarly, the green LED named P1.3_B is connected to the C8051F502 (Side B) through the J11
header. See Table 1 for the port pins and headers corresponding to each LED.
8.5. Target Board Debug Interfaces (P2 and P3)
The debug connectors P2 (DEBUG_A) and P3 (DEBUG_B) provide access to the debug (C2) pins of the
C8051F500 and C8051F502. The debug connectors are used to connect the Serial Adapter or the USB Debug
Adapter to the target board for in-circuit debugging and Flash programming. Table 2 shows the DEBUG pin
definitions.
Table 1. Target Board I/O Descriptions
Description
I/O
Header(s)
RESET_A
Reset (Side A)
none
RESET_B
Reset (Side B)
none
P1.4_A Switch
P1.4 (Side A)
J191–2]
P1.4_B Switch
P1.4 (Side B)
J11[1–2]
P1.3_A LED
P1.3 (Side A)
J19[3–4]
P1.3_B LED
P1.3 (Side B)
J11[3–4]
Red LED (PWR)
Power
none
Red LED (COMM)
COMM Active
none
Table 2. DEBUG Connector Pin Descriptions
Side A - C8051F500
Side B - C8051F502
Pin #
Description
Pin #
Description
1
Not Connected
1
Not Connected
2, 3, 9
GND (Ground)
2, 3, 9
GND (Ground)
4
C2D_A
4
P3.0_C2D_B
5
/RST (Reset)
5
/RST_B (Reset)
6
Not Connected
6
P3.0_B
7
/RST/C2CK_A
7
/RST/C2CK_B
8
Not Connected
8
Not Connected
10
USB Power (+5VDC from P2)
10
Not Connected
Summary of Contents for C8051F500
Page 18: ...C8051F500DK 18 Rev 0 1 9 Schematics Figure 5 C8051F502 Target Board Schematic Page 1 of 4 ...
Page 19: ...C8051F500DK Rev 0 1 19 Figure 6 C8051F502 Target Board Schematic Page 2 of 4 ...
Page 20: ...C8051F500DK 20 Rev 0 1 Figure 7 C8051F502 Target Board Schematic Page 3 of 4 ...
Page 21: ...C8051F500DK Rev 0 1 21 Figure 8 C8051F502 Target Board Schematic Page 4 of 4 ...
