manualshive.com logo in svg

Silicon Laboratories C8051T320, Manual

The Silicon Laboratories C8051T320 is a high-performance microcontroller designed for various applications. This versatile product offers a comprehensive user manual, which can be easily downloaded for free from 88.208.23.73:8080. Enhance your experience with this cutting-edge technology by accessing the detailed manual at your convenience.

Share
Download
background image

Rev. 1.2

115

C8051T620/1/6/7 & C8051T320/1/2/3

6. Make certain that all writes to the RSTSRC register explicitly set the PORSF bit to a 1. Areas to check 

are initialization code which enables other reset sources, such as the Missing Clock Detector, for 
example, and instructions which force a Software Reset. A global search on "RSTSRC" can quickly 
verify this.

18.3.2. PSWE Maintenance

7. Reduce the number of places in code where the PSWE bit (PSCTL.0) is set to a 1. There should be 

exactly one routine in code that sets PSWE to a 1 to write EPROM bytes.

8. Minimize the number of variable accesses while PSWE is set to a 1. Handle pointer address updates 

and loop variable maintenance outside the "PSWE = 1;... PSWE = 0;" area.

9. Disable interrupts prior to setting PSWE to a '1' and leave them disabled until after PSWE has been 

reset to '0'. Any interrupts posted during the EPROM write operation will be serviced in priority order 
after the EPROM operation has been completed and interrupts have been re-enabled by software.

10.Make certain that the EPROM write pointer variables are not located in XRAM. See your compiler 

documentation for instructions regarding how to explicitly locate variables in different memory areas.

11. Add address bounds checking to the routines that write EPROM memory to ensure that a routine called 

with an illegal address does not result in modification of the EPROM.

18.3.3. System Clock

12.If operating from an external crystal, be advised that crystal performance is susceptible to electrical 

interference and is sensitive to layout and to changes in temperature. If the system is operating in an 
electrically noisy environment, use the internal oscillator or an external CMOS clock.

13.If operating from the external oscillator, switch to the internal oscillator during EPROM write operations. 

The external oscillator can continue to run, and the CPU can switch back to the external oscillator after 
the EPROM operation has completed.

18.4.  Program Memory CRC

A CRC engine is included on-chip which provides a means of verifying EPROM contents once the device 
has been programmed. The CRC engine is available for EPROM verification even if the device is fully read 
and write locked, allowing for verification of code contents at any time.

The CRC engine is operated through the C2 debug and programming interface, and performs 16-bit CRCs 
on individual 256-Byte blocks of program memory, or a 32-bit CRC on the entire memory space. To prevent 
hacking and extrapolation of security-locked source code, the CRC engine will only allow CRCs to be per-
formed on contiguous 256-Byte blocks beginning on 256-Byte boundaries (lowest 8-bits of address are 
0x00). For example, the CRC engine can perform a CRC for locations 0x0400 through 0x04FF, but it can-
not perform a CRC for locations 0x0401 through 0x0500, or on block sizes smaller or larger than 256 
Bytes. 

18.4.1. Performing 32-bit CRCs on Full EPROM Content

A 32-bit CRC on the entire EPROM space is initiated by writing to the CRC1 byte over the C2 interface. 
The CRC calculation begins at address 0x0000, and ends at the end of user EPROM space. The EPBusy 
bit in register C2ADD will be set during the CRC operation, and cleared once the operation is complete. 
The 32-bit results will be available in the CRC3-0 registers. CRC3 is the MSB, and CRC0 is the LSB. The 
polynomial used for the 32-bit CRC calculation is 0x04C11DB7. Note: If a 16-bit CRC has been performed 
since the last device reset, a device reset should be initiated before performing a 32-bit CRC operation.

18.4.2. Performing 16-bit CRCs on 256-Byte EPROM Blocks

A 16-bit CRC of individual 256-byte blocks of EPROM can be initiated by writing to the CRC0 byte over the 
C2 interface. The value written to CRC0 is the high byte of the beginning address for the CRC. For exam-
ple, if CRC0 is written to 0x02, the CRC will be performed on the 256-bytes beginning at address 0x0200, 
and ending at address 0x2FF. The EPBusy bit in register C2ADD will be set during the CRC operation, and 
cleared once the operation is complete. The 16-bit results will be available in the CRC1-0 registers. CRC1 
is the MSB, and CRC0 is the LSB. The polynomial for the 16-bit CRC calculation is 0x1021.

Summary of Contents for C8051T320












































































































































































































































































































Reviews:

No comments

Related manuals for C8051T320

UniKey SR3 Installation Manual & User Manual preview
SR3
Brand: UniKey Pages: 20
Fantech ECO-TOUCH Operating Manual preview
ECO-TOUCH
Brand: Fantech Pages: 2
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
HANYOUNG NUX TS500 Manual preview
TS500
Brand: HANYOUNG NUX Pages: 56
Joy-it Moto1 Quick Start Manual preview
Moto1
Brand: Joy-it Pages: 7
Dungs 273061 Instructions Manual preview
273061
Brand: Dungs Pages: 56
Emec PH CONTROLLER Operating Manual preview
PH CONTROLLER
Brand: Emec Pages: 8
Qorvo QM33120WDK1 Quick Start Manual preview
QM33120WDK1
Brand: Qorvo Pages: 6
American Lighting TRULUX DMX 3Z Touch Control Installation Instructions Manual preview
TRULUX DMX 3Z Touch Control
Brand: American Lighting Pages: 2
Jandy AquaLink RS All Button Quick Review Card preview
AquaLink RS All Button
Brand: Jandy Pages: 2
elero BoxControl Compact Instruction Manual preview
BoxControl Compact
Brand: elero Pages: 8
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Brand: KEPCO Pages: 34
Greenheck 474706 Reference Manual preview
474706
Brand: Greenheck Pages: 32
HomeMatic HM-LC-Dim1T-DR Installation And Operating Manual preview
HM-LC-Dim1T-DR
Brand: HomeMatic Pages: 68
Linak TWINDRIVE TD1 Product Data Sheet preview
TWINDRIVE TD1
Brand: Linak Pages: 8
Translux Fair-Play MP-50 Series Quick Reference preview
Fair-Play MP-50 Series
Brand: Translux Pages: 20
W8ZR StationPro II Operating Manual preview
StationPro II
Brand: W8ZR Pages: 77

Brands by name

Popular brands

Load more brands