manualshive.com logo in svg

Silicon Laboratories EFM32G, Reference Manual

The Silicon Laboratories EFM32G is a premier microcontroller offering exceptional performance and energy efficiency. Explore its limitless potential with the comprehensive Reference Manual, available for free download from our website. Discover valuable insights and unleash the full potential of your EFM32G through this detailed and user-friendly manual.

Share
Download
background image

...the world's most energy friendly microcontrollers

2014-07-02 - Gecko Family - d0001_Rev1.30

326

www.silabs.com

continue running if triggered while it is running, so the multiple-triggering will only have an
effect if you try to disable the RTC when it is being triggered.

21.3.3.5 Debug

If DEBUGRUN in LETIMERn_CTRL is cleared, the LETIMER automatically stops counting when the
CPU is halted during a debug session, and resumes operation when the CPU continues. Because of
synchronization, the LETIMER is halted two clock cycles after the CPU is halted, and continues running
two clock cycles after the CPU continues. RUNNING in LETIMERn_STATUS is not cleared when the
LETIMER stops because of a debug-session.

Set DEBUGRUN in LETIMERn_CTRL to allow the LETIMER to continue counting even when the CPU
is halted in debug mode.

21.3.4 Underflow Output Action

For each of the repeat registers, an underflow output action can be set. The configured output action is
performed every time the counter underflows while the respective repeat register is nonzero. In PWM
mode, the output is similarly only changed on COMP1 match if the repeat register is nonzero. As an
example, the timer will perform 7 output actions if LETIMERn_REP0 is set to 7 when starting the timer
in one-shot mode and leaving it untouched for a while.

The output actions can be set by configuring UFOA0 and UFOA1 in LETIMERn_CTRL. UFOA0 defines
the action on output 0, and is connected to LETIMERn_REP0, while UFOA1 defines the action on output
1 and is connected to LETIMERn_REP1. The possible actions are defined in Table 21.2 (p. 326) .

Table 21.2. LETIMER Underflow Output Actions

UF0A0/UF0A1

Mode

Description

00

Idle

The output is held at its idle value

01

Toggle

The output is toggled on
LETIMERn_CNT underflow if
LEIMERn_REPx is nonzero

10

Pulse

The output is held active for one clock
cycle on LETIMERn_CNT underflow if
LETIMERn_REPx is nonzero. It then
returns to its idle value

11

PWM

The output is set idle on
LETIMERn_CNT underflow
and active on compare match
with LETIMERn_COMP1 if
LETIMERn_REPx is nonzero.

Note

For the Pulse and PWM modes, the outputs will return to their idle states regardless of the
state of the corresponding LETIMERn_REPx registers. They will only be set active if the
LETIMERn_REPx registers are nonzero however.

The  polarity  of  the  outputs  can  be  set  individually  by  configuring  OPOL0  and  OPOL1  in
LETIMERn_CTRL. When these are cleared, their respective outputs have a low idle value and a high
active value. When they are set, the idle value is high, and the active value is low.

When using the toggle action, the outputs can be driven to their idle values by setting their respective
CTO0/CTO1 command bits in LETIMERn_CTRL. This can be used to put the output in a well-defined
state before beginning to generate toggle output, which may be important in some applications. The
command bit can also be used while the timer is running.

Summary of Contents for EFM32G


























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EFM32G

T-Verter E2 Series Operating Manual preview
E2 Series
Brand: T-Verter Pages: 121
Happy 1050 Installation & Use Instructions preview
1050
Brand: Happy Pages: 10
EasyIO FG Series User Manual preview
FG Series
Brand: EasyIO Pages: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Brand: RMG Pages: 6
Aalborg DFC Operating Manual preview
DFC
Brand: Aalborg Pages: 48
Hach EC1000 Instruction Manual preview
EC1000
Brand: Hach Pages: 128
Yamato V Instruction Manual preview
V
Brand: Yamato Pages: 33
Idemia MorphoAccess SIGMA Extreme Series Quick User Manual preview
MorphoAccess SIGMA Extreme Series
Brand: Idemia Pages: 31
Valcom V-1092 User Manual preview
V-1092
Brand: Valcom Pages: 3
Valcom V-1092 Technical Specifications preview
V-1092
Brand: Valcom Pages: 2
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
National Instruments NI 9514 User Manual preview
NI 9514
Brand: National Instruments Pages: 72
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Brand: Webasto Pages: 8
V2 FORTECO 2500-I Manual preview
FORTECO 2500-I
Brand: V2 Pages: 108
Cruisair TWLC User Manual preview
TWLC
Brand: Cruisair Pages: 30
Fisher 1098-EGR Instruction Manual preview
1098-EGR
Brand: Fisher Pages: 44
NEEDO MY NEEDO User Manual Book preview
MY NEEDO
Brand: NEEDO Pages: 193
Danfoss ADAP-KOOL AK-CC 750 Service Manual preview
ADAP-KOOL AK-CC 750
Brand: Danfoss Pages: 6

Brands by name

Popular brands

Load more brands