manualshive.com logo in svg

Silicon Laboratories Giant Gecko EFM32GG, Reference Manual

The Silicon Laboratories Giant Gecko EFM32GG is a powerful microcontroller, designed for a wide range of applications. Unlock the full potential of this product by downloading the comprehensive "Reference Manual" from our website for free. Access detailed instructions and technical information to maximize your experience with the Giant Gecko EFM32GG.

Share
Download
background image

...the world's most energy friendly microcontrollers

2016-04-28 - Giant Gecko Family - d0053_Rev1.20

302

www.silabs.com

• If there is no space in the receive FIFO, interrupt data packets are ignored and not written to the

receive FIFO. Additionally, interrupt OUT tokens receive a NAK handshake reply.

2. When the packet count becomes 0 or when a short packet is received on the endpoint, the NAK bit

for that endpoint is set. Once the NAK bit is set, the isochronous or interrupt data packets are ignored
and not written to the receive FIFO, and interrupt OUT tokens receive a NAK handshake reply.

3. After the data is written to the receive FIFO, the core’s DMA engine reads the data from the receive

FIFO and writes it to external memory, one packet at a time per endpoint.

4. At the end of every packet write on the AHB to external memory, the transfer size for the endpoint

is decremented by the size of the written packet.

5. The OUT Data Transfer Completed pattern for an OUT endpoint is written to the receive FIFO on

one of the following conditions.
• The transfer size is 0 and the packet count is 0.
• The last OUT data packet written to the receive FIFO is a short packet (0 < packet size < maximum

packet size)

6. When either the application or the DMA pops this entry (OUT Data Transfer Completed), a Transfer

Completed interrupt is generated for the endpoint and the endpoint enable is cleared.

15.4.4.2.2.11 Generic Isochronous OUT Data Transfers Using Periodic Transfer Interrupt Feature

This  section  describes  a  regular  isochronous  OUT  data  transfer  with  the  Periodic  Transfer  Interrupt
feature.

To  initialize  the  core  after  power-on  reset,  the  application  must  follow  the  sequence  in  Overview:
Programming the Core (p. 250) . Before it can communicate with the host, it must initialize an endpoint
as  described  in  Endpoint  Initialization  (p.  285) .  For  packet  writes  in  Slave  mode,  see:  Packet  Read
from FIFO in Slave Mode (p. 294) .

Application Requirements

1. Before setting up ISOC OUT transfers spanned across multiple frames, the application must allocate

buffer  in  the  memory  to  accommodate  all  data  to  be  received  as  part  of  the  OUT  transfers,  then
program that buffer’s size and start address in the endpoint-specific registers.
• The application must mask the USB_GINTSTS.INCOMPLP (Incomplete ISO OUT).
• The application must enable the USB_DCTL.IGNRFRMNUM

2. For ISOC transfers, the Transfer Size field in the USB_DOEPx_TSIZ.XFERSIZE register must be a

multiple of the maximum packet size of the endpoint, adjusted to the DWORD boundary. The Transfer
Size programmed can span across multiple frames based on the periodicity after which the application
wants to receive the USB_DOEPx_INT.XFERCOMPL interrupt
• transfer size[epnum] = n * (mps[epnum] + 4 - (mps[epnum] mod 4))
• packet count[epnum] = n
• n > 0 (Higher value of n reduces the periodicity of the USB_DOEPx_INT.XFERCOMPL interrupt)
• 1  =<  packet  count[epnum]  =<  n  (Higher  value  of  n  reduces  the  periodicity  of  the

USB_DOEPx_INT.XFERCOMPL interrupt).

3. In DMA mode, the core stores a received data packet in the memory, always starting on a DWORD

boundary. If the maximum packet size of the endpoint is not a multiple of 4, the core inserts byte
pads at end of a maximum-packet-size packet up to the end of the DWORD. The application will not
be informed about the frame number and the PID value on which a specific OUT packet has been
received.

4. The  assertion  of  the  USB_DOEPx_INT.XFERCOMPL  interrupt  marks  the  completion  of  the

isochronous OUT data transfer. This interrupt does not necessarily mean that the data in memory
is good.
• On  USB_DOEPx_INT.XFERCOMPL,  the  application  must  read  the  endpoint’s  Transfer  Size

register to calculate the size of the payload in the memory.

• Payload size in memory = application-programmed initial transfer size - core updated final transfer

size

Summary of Contents for Giant Gecko EFM32GG












































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Giant Gecko EFM32GG

Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Brand: Baader Planetarium Pages: 7
YOKOGAWA CX1000 Installation And Connection Manual preview
CX1000
Brand: YOKOGAWA Pages: 2
Halma ALICAT SCIENTIFIC PC Quick Start Manual preview
ALICAT SCIENTIFIC PC
Brand: Halma Pages: 2
Halma ALICAT SCIENTIFIC PCD Operating Manual preview
ALICAT SCIENTIFIC PCD
Brand: Halma Pages: 46
Safran MorphoAccess SIGMA Extreme Series Installation Manual preview
MorphoAccess SIGMA Extreme Series
Brand: Safran Pages: 79
Lawler 805 Installation & Maintenance Manual preview
805
Brand: Lawler Pages: 5
Panosol SR658 Operation Manuals preview
SR658
Brand: Panosol Pages: 105
Pangolin FB4 Series Quick Start Manual preview
FB4 Series
Brand: Pangolin Pages: 8
NAiS FP2 Technical Manual preview
FP2
Brand: NAiS Pages: 144
Interlogix TruPortal TP-ADD-1DIP Quick Reference preview
TruPortal TP-ADD-1DIP
Brand: Interlogix Pages: 9
Danfoss AFD 2 VFG 2 Operating Manual preview
AFD 2 VFG 2
Brand: Danfoss Pages: 8
MAKOT UMS-04 Series Manual preview
UMS-04 Series
Brand: MAKOT Pages: 6
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Brand: Davey Pages: 8
Italtecnica Brio 2000 Owner'S Manual preview
Brio 2000
Brand: Italtecnica Pages: 16
Parker P3HPA Series Manual preview
P3HPA Series
Brand: Parker Pages: 22
Ulvac UK-2 Instruction Manual preview
UK-2
Brand: Ulvac Pages: 48
G-Scale Graphics LSCM2 Operation And Installation Manual preview
LSCM2
Brand: G-Scale Graphics Pages: 7
Electric Time 99B-MI User Manual preview
99B-MI
Brand: Electric Time Pages: 21

Brands by name

Popular brands

Load more brands