MESH-CEFL
Ceiling Flush Mount Passive Infra Red
(PIR) Occupancy Detector & Photocell
Input: 100-240 Vac 50/60Hz
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT
NOTE: MESH-CEFL is compatible with any qualifi ed Bluetooth mesh components and commissioning tools.
We recommend Silvair Commissioning as a reliable solution.
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388 E-mail: sales@danlers.co.uk
www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
11/10/19
INS372 MESH-CEFL (Issue 04)
TECHNICAL DETAILS
INPUT
Voltage:
100 - 240Vac
Frequency:
50/60Hz
Max. mains current:
20mA
Standby current:
14mA
RADIO TRANSCEIVER
Operating frequencies: 2.4... 2,480 GHz
Max. output power:
+4 dBm
LUX PARAMETERS
Range:
5 - 2000 lux
OPERATING CONDITIONS
Note: The temperature difference between the
detection target and the background must be at
least 4 °C.
Ambient temperature:
-20... +40 °C (lout
20mA)
Storage temperature:
-25... +75 °C
Max. relative humidity:
0... 80%, non cond.
CONNECTORS
Terminal block
Wire size:
0.5mm
2
- 2.5mm
2
solid
or stranded
Wire strip length:
6-7mm
Tightening torque:
0,4 Nm/4 Kgf.cm
MECHANICAL DATA
Dimensions:
79mm x 85mm x
85mm
Weight:
97g (unpacked)
Degree of protection:
IP40
Protection class:
Built-in Class 2
Material (casing)
Flame-retardant
polycarbonate
Finish / Colour
Matt /White (RAL 9003)
Protection class:
Built-in Class 2
CONFORMITY AND STANDARDS
EMC emission:
EN 301 489-1 V2.2.0,
EN 301 489-17 V3.1.1,
EN 55032: 2015,
EN61000-3-2: 2014,
EN61000-3-3: 2013
EMC immunity:
EN 301 489-1 V2.2.0,
EN 301 489-17 V3.1.1
Environment:
Complies with WEEE and RoHS directives
CB scheme:
IEC60669-1:1998,
IEC60669-1:1998/AMD1:1999,
IEC60669-1:1998/AMD2:2006,
IEC60669-2:2002,
IEC60669-2-1:2002/AMD1:2008,
This fl ush mounted MESH-CEFL is suitable for
easy mounting through a 73/75mm diameter hole
into a ceiling void which is at least 78mm deep.
Confi gurable for any room occupancy style, via the
Silvair Platform (App and Web).
INSTALLATION
To be installed by a competent person with
reference to BS 7671 or equivalent local standards.
If in doubt consult a qualifi ed electrician.
• Plan where the MESH-CEFL is to be located
(see diagram 1). Switch off supply and check
for hidden cables and pipes. Make a 73/75mm
diameter hole through a standard ceiling board.
• The MESH-CEFL should be connected as
shown in diagram 2:
L - Live in. N - Neutral in.
• Ensure both springs are fi tted to the moulding in
the correct orientation (see diagram 3).
• Push the MESH-CEFL into the ceiling void,
making reference to diagram 4.
OPERATION
To check the operation of the MESH-CEFL:
• Turn on the supply then after 20 seconds if the
sensor has recognised movement of a person
within its zone of detection the integral red
LED on MESH-CEFL will stay illuminated for 4
seconds before the red LED turns off.
• Thereafter, every time movement is detected
by MESH-CEFL the integral red LED will stay
illuminated for 4 seconds.
The control also features adjustable time out (time
lag) control and daylight threshold control which
are confi gured via the Silvair Platform.
PRECAUTIONS
• Do not place the MESH-CEFL near heat
sources, fans or in ventilated ceiling voids.
• MESH-CEFL can be wired in parallel (sharing
the same Live and Neutral).
• Do not place close to, or positioned such
that, any light source points directly into the
MESH-CEFL.
• Ensure wires and cables are securely held within
the connection terminals.
• The MESH-CEFL should be protected by a 5 or
6 Ampere mcb or fuse.
•
Disconnect the MESH-CEFL from the
circuit before performing insulation testing
of the wiring circuit.
DIAGRAM 2
Suggested typical wiring
N
L
230 Vac
5A or 6A MCB
or fuse
L
N
N
L
L - Live in. N - Neutral in.
Two neutral and two live terminals
are available for easy ‘loop in’ and
‘loop out’ connection.
Squeeze spring coils together and fi t
onto each of the two lugs in turn.
Repeat on opposite side of product .
DIAGRAM 3
Ceiling void at least 78mm deep. 75mm circular hole cut for MESH-CEFL.
DIAGRAM 4
up to 5m
up to 7m
Strong detection zone
i.e. person moving arm
or walking towards PIR
For optimum coverage recommended
mounting height: 2.4 to 5m
Secondary detection
zone i.e. person walking
perpendicular to PIR
DIAGRAM 1
DIMENSIONS, HALL EFFECT AND
FACTORY RESET:
See overleaf for details.
5 YEAR WARRANTY
MESH-CEFL comes with a 5 year
warranty from the date of manufacture
and is CE marked.
