background image

 

 

WARNINGS   

 

This  sprayer  is  designed  and  manufactured  solely  for  the  purpose  of  applying 
agricultural chemicals. Under no circumstances may it be used for any other purpose. 

 

Read owner’s manual completely before operati

ng this sprayer. 

 

Test the sprayer with water before using chemicals 

 

Before  using 

chemicals  refer  to  the  chemical  manufacturer’s  label  and  safety 

instructions  for  safe  handling  procedures  and  the  recommended  personal  protective 
clothing and safety equipment. 

 

Spray when air is calm to prevent drift of chemicals. 

 

Always  release  pressure  when  sprayer  is  not  in  use  and  before  performing  any 
maintenance. 

 

Do not leave sprayer in the sun when not in use. 

 

Never use flammable liquids, caustics, acids, or hot water in this tank. 

 

Do not use sprayer near open flame or anything that could cause ignition of the spray. 

 

Always inspect the hose and all hose connections before each use. A damaged hose, or 
loose hose connection can result in unintended exposure to the pressurised chemical, 
resulting in serious injury or property damage. 

 

Do not pressurize with any mechanical device such as an air compressor since this can 
create a dangerous pressure level and bursting of parts resulting in serious injury. Only 
use original pump. 

 

Do not lift or carry sprayer by the hose, shut-off valve, or wand extension. Carry by the 
handle only. 

 

Do not store chemicals in this tank. 

 

Clean and rinse sprayer thoroughly after each use and before and maintenance. 

 

Never attempt to alter sprayer from original condition. 

 

Exercise  care  to  ensure  proper  stability  when  carrying  or  operating  in  hilly  or  uneven 
terrain, particularly if the ground is wet or loose. Wear non-slip shoes 

 

Keep the sprayer and all chemicals out of the reach of children. 

If you experience problems or have questions in Australia, please contact our toll-free Customer 
Service  Centre  at  1300  745  826,  or  email:  info@silvanaust.com,  or  access  online  at: 

www.silvan.com.au

 

In New Zealand phone 0508 745826or email: infonz@silvanaust.com 

WARRANTY: This product is warranted to be free from defects in materials and workmanship for the warranty period 
of 5 years from the date of retail sale. In the event of failure return the goods to the place of purchase at your cost 
and within the warranty period along with evidence of the purchase date. If the fault is assessed to be a failure due to 
faulty  materials  or  manufacturing,  then  the  product  will  be  repaired  or  replaced  without  charge  for  labour  or  any 
defective  parts.  If  the  original  supplier  cannot  be  contacted,  then  contact  Silvan  and  we  can  direct  you  on  how  to 
proceed with your warranty claim. Our goods come with guarantees that cannot be excluded under the Australian  & 
New Zealand Consumer Law.  

 

 

Safety Instructions 

 

 

Summary of Contents for 190547












Reviews: