background image

 Troubleshooting

Common problems

Cause

Solution

●The indicating light  in  ●The power is cut off.

●Check if the socket is well 

  front of product is OFF.

●The socket is not well 

   connected.

   

   connected.

●Check if there is any failure of 

●Failure of socket.

   socket.

●The iron can't be

●The automatic thermoregulator ●Adjust the automatic thermoregulator 

   heated up.

   is set at lowest position.

   to necessary position.

●The temperature of base plate  ●The base plate of iron is heating up,
   of iron is too low.

   pls wait for completion.

●The switch in front of product  ●When heating up is impossible with 
   is turned to OFF.

   above measures, pls contact your 
   agent for repair. 

●The iron runs normally,  ●There is no water in bucket.

●Add water to bucket.

   but steam amount is 

●The steam boiler in front of 

●Turn the switch to ON, waiting for

   little or no steam is 

   product is closed.  

   lighting up of indicating light. 

   produced. 

●The steam indicating light is 

●Wait for steam indicating light to be 

   not ON.

   ON.

●The steam hole at base plate  ●Contact your agent for repair when
  of iron is blocked.

    no steam is produced after taking  
    above measures.

●Water jets out from 

●Too much water in bucket.

●Observe the water volume in 

   base plate of iron.

●Auto thermoregulator is at low    bucket,and pour it out when there    
   temperature position.

  is too much water

●The base plate of iron is at 

●Adjust the automatic thermoregulator 

   middle positoin.

   to necessary position.
●Wait for heating completion of base 
   plate of iron.

●The steam ejects out

●Cut off power and connect the 

   continuously,the 

   agent for repair.

   solenoid valve can 
   not be closed.
●There is sufficient 

●Cut off power and connect the

   water in bucket, but 

   agent for repair.

   the steam indicating 
   light is not ON.
●The safety valve is 

●Cut off power and connect the 

   closed, but there is 

   agent for repair.

   still air leakage.
●The pressure gauge

●Cut off power and connect the

   points to over 4.5bar. 

   agent for repair.

●During use, the steam

●No abnormality present, pls 

   indicating light is

  don't worry.

   twinkling.
●During use, spot may 

●The inappropriate liquid or 

●Refer to page 10 for inappropriate 

   be left on clothes.

   unclean water is used.

   water. Tap water should be used. 

13

Summary of Contents for SIT-300














Reviews: