DE/AT/CH 49
7. Das Display zeigt nun die Minutenzahl (00). Mit
der Plus-
8
und Minus-Taste
7
können Sie die
gewünschte Minutenzahl einstellen (00-59).
8. Die Einstellungen können durch das Drücken der
OK-Taste
5
gespeichert und das Einstellungs-
Menü wieder verlassen werden.
9. Nach dem Einstellen der System-Zeit wird im
Display „P1“ angezeigt.
10. Warten Sie 10 Sekunden ohne irgendeine Taste zu
betätigen. Die System-Einstellungen werden dann
übernommen. Die Umgebungstemperatur wird auf
dem Display angezeigt. Gegebenenfalls können Sie
mit der Programmwahl P1, P2... P6 fortfahren. Mehr
dazu im Abschnitt Wochen-Timer.
Hinweis:
Um die Systemzeit zurückzusetzen, muss das
Gerät ausgeschaltet und
von der Stromver sorgung
getrennt werden.
WOCHEN-TIMER
Der Wochentimer dient dazu den Keramik
Wandheizlüfter zu bestimmten Zeiten au-
tomatisch ein- und auszuschalten. Bei der
Einstellung des Wochen-Timers stehen Ih-
nen fünf voreingestellte Programme sowie
ein manuell einzustellendes Programm
zur Verfügung. Sobald die Funktion akti-
viert ist, schaltet sich das Gerät nach dem
entsprechenden Zeitplan automatisch ein
oder aus.
Hinweis:
Es ist nicht möglich, den Wochen-Timer zu
starten, solange sich das Gerät im Ventilator-Modus
befindet.
Hinweis:
Es ist nicht möglich den Wochen-Timer einzu-
stellen ohne davor die Systemzeit eingestellt zu haben
(siehe Systemzeit-Einstellung)
EINSTELLUNG DER TIMER-PROGRAMME 1-5
(VOREINGESTELLTE PROGRAMME)
1. Schalten Sie das Gerät ein (siehe Inbetriebnahme).
2.
Wählen Sie die erste oder die zweite Heizstu-
fe aus. Drücken Sie dafür die Heizstufen-Taste
11
. Das Symbol
A
am Display leuchtet. S.
Abschnitt Heizstufen-Einstellung. Alternativ kön-
nen Sie eine gewünschte Temperatur auswählen
(siehe Abschnitt Temperatur-Einstellung).
Hinweis:
Der Keramik Wandheizlüfter wird sich dann je
nach ausgewähltem Programm einschalten und die Ein-
stellung der Heizstufe bzw. der Temperatur übernehmen.
3. Drücken Sie die Wochen-Timer-Taste
9
:
4. Es folgt die Anzeige des Timer-Programmes auf
dem Display. Mit jedem Drücken der Taste
9
wechselt man zum nächsten Programm P1-P2-P3-
P4-P5-P6-Aus. (siehe Programm-Tabelle auf der
hinteren Ausklappseite)
5. Bestätigen Sie Ihre Auswahl mit der OK-Taste
5
.
6.
Je nach im Punkt 4 ausgewähltem Programm
und je nach Zeitpunkt (Tag und Uhrzeit) leuchtet
die Wochen-Timer-Anzeige
B
im Display oder
blinkt sie.
Wenn die Anzeigen
A
und
B
kontinuierlich leuch-
ten, ist das ausgewählte Programm aktiv bzw. das
Gerät schaltet automatisch aus.
Wenn die Anzeigen
A
und
B
blinken, ist das
ausgewählte Programm noch nicht aktiv. Das Gerät
schaltet sich dann nach 30 Sekun den wieder aus.
Der Ventilator läuft währenddessen nach bis zu
Standby. Die Anzeigen
A
und
B
blinken weiter
bis das Programm automatisch greift und das Gerät
einschaltet.