4
GB
Noise and Vibration
Sound and vibration levels in the specification are determined according to
ISO 28927-3. The figures given can be used to compare similar tools tested
to this standard. These figures may be used to assess exposure to noise
and vibration levels.
The figures represent normal use for the tool in normal working condition.
A poorly maintained, incorrectly assembled or misused tool may produce
increased levels of noise and vibration. The total working period that
you can operate this tool must factor in periods where the tool is idle or
switched off. Allow frequent rest breaks when operating this tool.
It is in the interest of users to maximise their safety using the correct safety
equipment, like ear defenders that protect against loud or repetitive noise,
and anti-vibration gloves that minimise vibration. Do not operate the tool
with your hands below a normal comfortable temperature, as vibration will
have a greater effect.
Sound
The noise directive was introduced to protect against the risk to health and
safety arising or likely to arise from exposure to noise and risk of hearing.
The Directive can be used to define noise exposure and the physical
parameters, such as peak sound pressure and daily and weekly exposure
level. Particular attention should be taken to exposure level and duration.
For more information on the Noise Directives 2003/10/EC and 2000/14/
EC, please visit The European Agency for Safety and Health at work -
www.
osha.europa.eu.
Vibration
The European Physical Agents (Vibration) Directive 2002/44/EC was
introduced to control the exposure of vibration at work. The Directive
enables users of tools to make informed decisions on the amount of time
spent working. Those who regularly operate high vibration equipment over a
sustained period of time are at a higher risk of health problems. ISO 28927-
3 measures vibration in three directions which is known as tri-axial or
vector sum measurement. When operating high vibration equipment, ensure
not to exceed exposure levels. For more details on The Vibration Directive
2002/44/EC please visit The European Agency for Safety and Health at work
-
www.osha.europa.eu
General Safety
• For multiple hazards, read and understand the safety instructions before
installing, operating, repairing, maintaining, changing accessories on, or
working near this tool. Failure to do so can result in serious bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of
safety measures and increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and
markings required by this part of ISO 11148 are legibly marked on
the tool. The employer/user should contact the manufacturer to obtain
replacement marking labels when necessary
WARNING:
This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience
or knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the
appliance.
Projectile Hazards
• Be aware that failure of the workpiece or accessories, or even of the tool
itself, can generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool.
The grade of protection required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed
Entanglement Hazards
• Choking, scalping and/or lacerations can occur if loose clothing, personal
jewellery, neck wear, hair or gloves are not kept away from the tool and
its accessories
Specification
Maximum operating pressure: ..............................4bar (58psi)
Working pressure: ................................................3.5bar (50psi)
Air Inlet: ................................................................¼" BSP, supplied with
two male airline quick connectors (EN-6 ‘UK’ and EQ-4 ‘European’ types)
Spray gun body material:......................................Powder-coated cast
aluminium
Paint container material: .......................................Aluminium
Paint container volume: ........................................1000cm
3
Type of feed: .........................................................Suction
Nozzle diameter: ...................................................1.5mm
Fluid output: .........................................................130-210ml/min
Min. hose diameters:.. 8mm (5/16") for supply hose length up to 15m
9.5mm (3/8") for longer supply hoses
Air consumption: ..................................................85-227L/min (3-8cfm)
Weight: .................................................................0.75kg
Noise and vibration information:
Level of sound pressure according to Machinery directive 2006/42/EC:
Sound Pressure ....................................................L
PA
= 77dB(A)
Sound Power ........................................................L
WA
= 88dB(A)
Uncertainty ...........................................................K = 3dB
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measures are necessary.
Vibration total values (triax vector sum) according to Machinery directive
2006/42/EC:
Vibration emission value ......................................a
h
= 1.85m/s
2
Uncertainty
..........................................................K = 1.5m/s
2
As part of our ongoing product development, specifications of Silverline
products may alter without notice.
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Caution!
Toxic fumes or gases!
Risk of fire!
Risk of explosion!
NO open flames!
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
196536_Z1MANPRO1.indd 4
04/07/2013 17:48
Summary of Contents for 196536
Page 2: ...2 1 2 3 4 5 6 7 8 9 10 11 12 13 196536_Z1MANPRO1 indd 2 04 07 2013 17 48...
Page 52: ...52 NL NL Assembly Diagram 196536_Z1MANPRO1 indd 52 04 07 2013 17 49...
Page 54: ...54 NL NL Notes 196536_Z1MANPRO1 indd 54 04 07 2013 17 49...
Page 55: ...www silverlinetools com 55 Notes 196536 196536_Z1MANPRO1 indd 55 04 07 2013 17 49...
