background image

E

N

C

A

R

A

V

A

N

 S

P

D

U

-5

2

   

Table of contents

1. Introduction .......................................................................... 3

2. Safety .................................................................................... 3

3. Overview .............................................................................. 4

4. Installation ............................................................................ 4

4.1

Mounting ........................................................................................................... 4

4.2

Cables ................................................................................................................. 5

4.3

SICOM Panels ..................................................................................................... 5

4.4

Resistance & Voltage Inputs ............................................................................. 6

4.5

4 Stage Level 1 & 2 ............................................................................................. 6

4.6

Batteries, Chargers, Ground, Main Switch ....................................................... 7

4.7

Relays, Inputs ..................................................................................................... 8

5. Connecting ............................................................................ 8

5.1

Diagram .............................................................................................................. 9

6. Technical specifications ...................................................... 10

7. Troubleshooting ................................................................. 11

7.1

Shunt Sensors not visible ................................................................................ 11

Summary of Contents for CARAVAN SPDU-52












Reviews: