740P Evolution
Series
12
3.
To disable the 12 Volt trigger, press “OK” and “B1 ?
Y” appears in the display; rotate the volume control
to alternate from “Y” to “N” .
4.
Press “OK” and “SAVED” will appear brielfy in the
display followed by “B1 : N”.
5.
To configure another input, rotate the volume
control until that input appears in the display, then
press “OK”.
6.
Repeat steps 3 and 4.
7.
When you have finished with all of the inputs for
the “TRIGGER” press the “Setup” button and
“TRIGGER” will appear in the display. From this
point you can (i) exit from the Setup procedure by
pressing the “Setup” button again and “EXITING”
will appear in the display or (iii) continue with the
Setup procedure by disabling the infrared remote
sensor, changing the IR codes, resetting the
700i
back to factory default status (see the following
examples) or configuring more inputs (example on
previous page).
If you want to control the
MOON 740P
using a wired
aftermarket infrared remote control receiver with a
universal remote control, you can disable the IR sensor
located on the front panel as follows:
1.
You may either continue where we left off in the
previous example by pressing “Setup” twice to
return to the main menu and the turn the volume
control until “INFRARED” appears in the display OR
enter into the “Setup” mode from the beginning by
pressing the “Setup” button and rotating the
volume control until “INFRARED” appears in the
display.
2.
Press “OK” and “NORMAL” will appear in the display.
3.
To disable the
MOON 740P’s
front panel IR sensor,
rotate the volume control to alternate from
“NORMAL” to “DISABLED” .
4.
Press “OK” and “SAVED” will appear briefly
in the
display followed by “INFRARED”
5.
Press the “Setup” button to exit from the Setup
menu.
The
MOON 740P
is equipped with a rear mounted IR
input for use with aftermarket wired infrared remote
control receivers. In the event that you want control the
MOON 740P
with a universal remote control and
NOT
the one included (FRM-3), you can change the RC-5
remote control system codes. This procedure is
recommended when you have a large custom install
setup that uses multiple integrated amplifiers and/or
preamplifiers that operate on the RC-5 standard and
you need to make each component unique w.r.t.
remote control operation – up to 4 components. Before
making the following change, you should have a basic
understanding how to program a universal remote
control. The following example shows how to change
the IR codes that the
MOON 740P
will recognize:
1.
You may either continue where we left off in the
previous example by pressing “Setup” twice to
return to the main menu and the turn the volume
control until “IR CODE” appears in the display OR
enter into the “Setup” mode from the beginning by
pressing the “Setup” button and rotating the
volume control until “IR CODE” appears in the
display.
2.
Press “OK” and “DEFAULT” will appear in the
display.
3.
To change the RC-5 system codes, rotate the
volume control to scroll through the available sets
of RC-5 compatible codes: “SYS11”, “SYS14”,
“SYS15”, and “SYS19”.
4.
Once you’ve decided on one, Press “OK” and
“SAVED” will appear briefly
in the display followed
by “IR CODE”.
5.
From this point you can (i) exit from the Setup
procedure by pressing the “Setup” button again
and “EXITING” will appear in the display or (iii)
continue with the Setup procedure by disabling the
infrared remote sensor, changing the IR codes,
resetting the
740P
back to factory default status
(see the following example), configure the 12 Volt
Trigger Output or configure more inputs (examples
on previous pages).
Reset the MOON 740P software settings back to their
factory defaults:
