background image

 

SECTION 4 Safety 

1.

 

Read instruction manual before installing or operating device. 

2.

 

This unit is equipped with a 3-prong grounding plug and must be plugged into a 
3-terminal grounded receptacle. Do not defeat the grounding by modifying the 
plug or using an ungrounded 3-prong adapter, If an extension cord is necessary, 
use only a 3-wire extension cord that provides grounding. 

3.

 

Do not insert objects through intake or outlet grille. 

4.

 

Do not operate unit in flammable or explosive atmospheres. 

5.

 

Internal repairs or servicing must be done by qualified personnel. 

 

SECTION 5 Installation 

The BLOWER OVERHEAD is designed for permanent operation. The overhead 
blower can be used in permanent operation by hanging it to a sturdy flat surface such 
as a wall or under a shelf.   
 
For extremely dirty environments, an optional air filter may be installed. The air 
filter consists of a filter retainer and an air filter element. 
 
The BLOWER OVERHEAD should be placed approximately 1 to 3 feet from the 
critical work area or objects to be neutralized. It should be positioned to cover as 
much of the area as possible with the ionized air stream.   
 
The BLOWER OVERHEAD, part number OVERHEAD-120VAC, requires 120 
VAC 60 Hz for proper operation. The unit must be grounded for safe operation. Plug 
the unit into a standard 3-terminal grounded receptacle. If an extension cord is 
necessary, use only a 3-wire extension cord that provides grounding. 
 
The BLOWER OVERHEAD, part number OVERHEAD-230VAC,requires 230 
VAC 50 Hz for proper operation. The unit must be grounded for safe operation. The 
unit comes with line cord, without plug. A plug must be installed on the line cord for 
operation. Installation of the plug must be performed by qualified personnel. The 
color code for wiring the plug is as follows: Brown – Line; Blue – Neutral; 
Green/Yellow – Ground. 
 
Under the unclean environment, please set the filtration attached. 
This filtration includes a fixture and a carbon filter. 
Put the carbon filter inside the fixture, then fix the fixture to the plastic shield. Press 

Summary of Contents for OVERHEAD Series










Reviews: