background image

52

EN

6  WARRANTY TERMS AND 

CONDITIONS AND LIMITATIONS

The warranty is only valid when the following water quality cha-

racteristics are satisfied:

–  Saturation index (Langelier): LSI > 0.1
–  Corrosivity index (C.I.): 0.5 < C.I. < 3
–  Where C.I. = 

c(CI) + c(NO

3

) - 2c(SO

4

-2

)

c(HCO

3

)

 (HCO

3

)> = 2.0 mmol/l

In such case, the magnesium anode must be replaced every 

year.

–  When C.I. > 3, the warranty is limited to two years and the ma-

gnesium anode must be replaced every six months.

–  For stainless steel tanks: the warranty is valid if the water used 

has a chlorine saturation value of maximum 200 mg/l [c(CL-) 

< 200 mg/l].

–  In areas in which the water has a saturation value of CaCO

3

 

ranging from 54 to 90 mg/l, we recommend using a water 

softening device to prevent calcium carbonate and other cal-

cium deposits from forming. If the saturation value exceeds 90 

mg/l CaCO

3

, this device is mandatory.

General terms and conditions:

The warranty takes effect from the date of installation and 

initial start-up of the device.

The heating element and the thermostat are covered for a 

period of two years.

Damages due to natural disasters, force majeure, earth-

quakes and extreme frost are not covered.

Damages due to improper use, incorrect installation, and 

incorrect electrical wiring are not covered.

The warranty shall not apply if the appliance is installed 

or subjected to maintenance by unauthorised personnel.

All parts used for maintenance and/or repairs must be ori-

ginal or equivalent.

Secondary damages caused by water leakages, etc. are 

not covered.

Claims will not be covered if the warranty document has 

not been filled in and a copy has not been sent to the ma-

nufacturer and/or distributor or local authorised dealer.

The warranty shall not apply if routine maintenance has 

not been carried out.

10 

The table of routine maintenance activities shown below 

must be filled in and signed. Additional proof may be re-

quested (e.g. invoice of the works).

11 

The warranty does not apply if the salinity of the water 

used exceeds 500 ppm.

12 

The validity period of the warranty will not be renewed if 

any repairs are carried out within the period covered by 

the warranty.

13 

The warranty is limited to the cost for workmanship requi-

red for replacing and/or repairing the defective parts. Loss 

or secondary damages are not covered.

14 

The costs for transporting the defective materials, and tra-

vel and lodging expenses for technicians are not covered.

15 

If continuous high temperatures are expected and the 

collectors have been oversized due to the unfavourable 

installation position during certain periods of the year, it 

is mandatory to install a thermostatic safety valve or an 

expansion vessel on the primary circuit (solar). The war-

ranty shall be voided if the thermostatic valve or expansion 

vessel are not installed.

16 

Routine maintenance is mandatory for the warranty to be 

considered valid.

7  DISPOSAL

7.1 

Disposal of the equipment (European 

Directive 2012/19/EU)

At the end of their life span, the appliance and 

electrical and electronic devices deriving from 

professional facilities or classifiable as profes-

sional waste, must be delivered to appropriate 

waste collection systems, in accordance with the 

law and with Directive 2012/19/EU. 

This product was designed and manufactured 

for minimising its impact on the environment 

and on human health, nonetheless it contains 

components that could be detrimental if mana-

ged improperly. 

The symbol (crossed-out wheelie bin) depicted 

here and also appearing on your product indica-

tes that the appliance at the end of its life must 

be treated in accordance with the law and dispo-

sed of as electrical and electronic waste. 

Before delivering the appliance for its disposal, 

consult the applicable provisions of the laws in 

force in the country where the appliance is used 

and obtain information on the authorised waste 

collection facilities, by contacting the local offi-

ces of the place where the appliance is installed.

IT IS FORBIDDEN

to dispose of the product together with urban waste.

Summary of Contents for NATURAL 300/8.16 S

























































Reviews: