17
16
Warranty
Technical Specifications / Troubleshooting
10. Warranty
Always keep your receipt as proof of purchase.
We’re here to help! If you have any questions or comments, call our toll-free hotline 1-866-4SIMONIZ (1-866-474-6664). Have your
serial number ready. The serial number can be found on the back plate, located on the rear of the unit.
One-(1) year Warranty
This Simoniz product carries a
One (1) year
manufacturer’s warranty against defects in workmanship and materials. This product is
not guaranteed against wear or breakage due to misuse and/or abuse.
You may purchase accessories directly through place of purchase, or by calling our toll-free hotline 1-866-4SIMONIZ (1-866-474-6664).
This warranty does not cover accidental damage, unreasonable use, normal wear and tear, use of improper detergents, neglect, or
non-compliance with the Operating Instructions. The warranty does not cover loss of use or other consequential damages arising from
any of the above, nor does it cover repairs made or attempted by unauthorized persons.
The warranty is void if the equipment is used for commercial, rental or industrial purposes.
If you have further questions, please visit our website (www.simoniz.ca) or call 1-866-4SIMONIZ (1-866-474-6664).
8. Technical Specifications
Rated Speed
3200 RMP (no load)
Protection Class
II
Weight
5 lb 4 oz (2.28 kg)
AC Output Voltage
120 V, 60 Hz, 0.75 A
Rated Capacity
10" (25.4 cm)
•
The level of sound felt by the user could exceed 85dB (A) and ear protection measures must be taken.
•
The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing
one tool with another.
•
The declared vibration total value may also be used in a preliminary assessment of exposure.
WaRnInG
•
The vibration emission during actual use of the power tool can differ from the declared total value depending on the situation in
which the tool is used.
•
Wear appropriate hearing protection taking into consideration an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition
to trigger time).
9. Troubleshooting
ImPORTanT
If your unit still is not functioning properly once you have used this guide please call the SIMONIZ Toll-free service number at
1-866-4SImOnIz
(1-866-474-6664). Please do NOT bring the unit back to the store until you have called this number.
PROBlEm
POSSIBlE CaUSE
SOlUTIOn
The motor does not
run or start.
The power plug is not plugged in.
Plug the power plug into a suitable electrical outlet.
The tool is not switched on.
Press the on/off switch to switch on the tool.
The extension cord is the wrong wire
gauge or is too long.
Check Extension Cords for the proper wire gauge and cord length.
Polishing bonnet is
burned.
The bonnet stays at a spot of the work
surface during operation.
Avoid keeping the bonnet on the same work surface, even for a
short period of time. Instead, keep the tool moving constantly.
Work surface is
scratched.
The polish is too aggressive.
With polishing, remember to BE PATIENT and learn how the polish
works and breaks down and always start with the least aggressive
pad/polish to get the job done.
Swirls or hazing still
on the work surface
after operation.
The polish does not work into the surface
completely.
Work the polish in using slow, overlapping movements.
Poor lighting conditions.
Without proper lighting, the majority of swirls and scratches are
not visible. Try to use under controlled lighting.
Bonnet is too dirty or worn out.
Replace with a new bonnet regularly.
Wax applicator
continually comes
off the foam pad
during use.
Too much wax is applied.
Remove the waxing applicator and clean it thoroughly. Dry it fully
and re-attach it to the foam pad for use.
If necessary, replace it with a new applicator.
039-9055-6-Polisher kit-EN-FR-02.indb 16-17
11/9/12 4:10 PM
