Simplek Pro Operation Manual Download | Manualshive

Page: 16 / 16

background image

Environmental protection and disposal

Please take into account that the device must not
be disposed of with household waste.

Warranty

Insofar as the device was purchased as a consumer within the EU, the respective transposition of Directive 2011/83

/ EU into national law, with regard to the minimum standard of warranty, applies. In countries outside the EU, the

respective valid minimum warranty claims apply

Gildemeisterstr. 135
33689 Bielefeld
WEEE-Reg.-Nr.: DE 98571170
info@simplek.de

«
...
14
15
16

Summary of Contents for Pro

















Reviews:

No comments

Related manuals for Pro

Brand: Back View Pages: 168

Brand: Vega Pages: 2

Brand: Vega Pages: 11

Brand: S-BOL Pages: 3

Brand: K&M Pages: 3

Brand: Dometic Pages: 162

Brand: S+S Regeltechnik Pages: 16

Brand: Alpha Arsenal Pages: 15

Brand: Suunto Pages: 5

Inflatable Stand Up Paddle Board

Brand: Kings Adventure Pages: 3

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

TABFZ-G1-HS1117

Brand: Tablet EX Gear Pages: 2

RevitaSpa RS-L305A

Brand: Air innovations Pages: 12

Brand: Lexicon Pages: 14

Brand: V-TAC Pages: 136

Brand: Citiwell Pages: 1

Brand: JOBO Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands