background image

AUTOCALL TFX Fire Control System Operator’s Manual

26

the control panel to recognize the alarm. Approximately 10 seconds later, the panel will reset the

zone of conventional detectors for 45 seconds. During this time, make sure the tested detector is

clear of smoke, then proceed to test the next detector.

The panel will increment the LCD display counter for each recorded detector activation.

Solo Test Sounders ------

This function allows signalling appliances to be tested without first raising an alarm. It is possible

to test either ALL the signalling appliances, or the signalling appliances in

one

zone only. Proceed as follows:

1. Select the “Solo Test Sounders”option from the Test System menu. The display will respond with the

following message:

Zone no:

(Yes=all)

A blinking cursor indicates that an operator input is required. Entering zone “0”will cause only the common

indicating appliances to be tested.

2. Enter the number of the required zone and press

YES/ENTER

.

3. The display will respond with the following message:

sounders in

Solo test

exit with quit

All signalling appliances (in the selected zone) will operate for approximately 2 seconds every 30 seconds.

4. Walk around the site to all indicating appliances. Check for correct operation of the indicating

appliances.

5. When all the indicating appliances have been checked, press

QUIT

. The display will respond with

the following message:

Solo test terminated

6. The Solo test function will automatically terminate one hour after the solo test is completed, if not ter-

minated manually. If an alarm occurs during the solo test, the function will be automatically terminated

and the AUTOCALL TFX-500M/800M panel will respond as described in Section 1.1, “Quick

Response------Alarm.”

3.7. Isolate Menu

This menu selection allows for devices to be isolated so they do not respond to an alarm. Zones and points may be

temporarily isolated (taken out of service) for many reasons------device repair, circuit repair, etc. Only Customer Manager

status levels and above may access these menu options.

Figure 3--7 Isolate menu options sequence.

s

s

t

Y

N or

t

Y

N or

Y

Next Menu

Do you want to

isolate points?

isolate zone?

(sensors only)

isolate point?

(adr. loop only)

Do you want to

de--isolate pts?

Zonal isolation

Point isolation

Note: When system points are isolated, the SYSTEM TROUBLE LED and ZONE

TROUBLE LED related to the isolated point(s) are lighted continuously and the front

panel buzzer will sound intermittently.

firealarmresources.com

Summary of Contents for TFX-500M













































Reviews: