background image

29

If an attempt is made to de-isolate a zone which is already de-isolated, the display will respond with the following

message:

Point(s) already de-isolated

If a printer is connected and on-line, each zone enabled will be logged in the following format:

POINT ENABLED 3rd Floor 12:44:00 23 Jan 90
Non Addressable Pnt. Zone 1

In this example, Zone 1 [all points] has been enabled.

De-Isolate Point (Communication Circuits Only)

------ Previously isolated individual devices specified by their

addresses may be de-isolated. Proceed as follows:

1. Select the “De-Isolate Point”option from the menu. The display will respond with the following mes-

sage:

Loop: A

(Y/N)?

2. If the device to be de-isolated is on Loop A, press

YES/ENTER

. Go to Step 8 and proceed.

3. If the required device is NOT on Loop A, press

NO/DELETE

The display will respond with the fol-

lowing message:

Loop: B

(Y/N)?

4. If the device to be de-isolated is on Loop B, press

NO/DELETE

. Go to Step 8 and proceed.

5. If the required device is NOT on Loop B, press

NO/DELETE

. Continue until the correct loop is cho-

sen.The display will respond with the following message:

Loop: A 1

(Y/N)?

6. If it is required to de-isolate the SAME numbered point on ALL loops, press

YES/ENTER

. Go to

Step 8 and proceed.

7. If a mistake is made, press

NO/DELETE

. The display will return to that shown in Step 1 above.

8. Once the correct loop has been chosen, the display will respond with the following message:

Point no.:

(0=none,Yes=all)

9. Enter the address of the required device and press

YES/ENTER

. The AUTOCALL

TFX-500M/800M panel will pause briefly and then display:

de-isolate successful

The ZONE TROUBLE yellow LED will go out, and the internal buzzer will stop sounding, if no further

points are isolated. The LCD will return to the “De-Isolate Point (addr. loop only)”display, allowing a

further point to be de-isolated.

If a non-existent address is entered, the display will respond with the following message:

Point(s) not

found

If an attempt is made to de-isolate a device which is already de-isolated, the display will respond with the

following message:

Point(s) already de-isolated

If a printer is connected and on-line, each point de-isolated will be logged in the following format for Loop A, point

16:

POINT ENABLED 3rd Floor Hall 12:54:00 23 Jan 90

“Point Label text” Zone 1 A16

In this example, Point A16 in Zone 1 has been de-isolated.

3.9. Open VFP (Open Virtual Front Panel)

The “Open VFP,”open virtual front panel, menu option is available only to TFXnet network systems. This option allows any

network panel to act as the front panel for any other network front panel. For example, if you are operating network panel

number 4, you may open a virtual front panel to network panel number 6 as follows:

firealarmresources.com

Summary of Contents for TFX-500M













































Reviews: