background image

3

SimpliFire •  Scion Trinity Floating Mantel Instruction Manual  •  2043-970 Rev. B  •  9/20

Figure 3   3/16 Toggle-Bolt Anchor

Framed Wall

•  Locate the mounting bracket on the wall in the 

desired location of the appliance.  Level the bracket, 

then mark its location on the wall, including a mark

-

ing for each of the fastener holes in the bracket.     

• 

For each of the marked mounting point locations, 

determine which points align with a structural fram-

ing member.  A minimum of two (2) locations must 

be secured into a framing member.  

•  At the points where a wood or metal framing mem-

ber exists, the ST6X50 screw can be installed 

directly into that structural member.  

•  For every mounting hole that does not align with a 

structural framing member, a wall board toggle-bolt 

anchor must be used. See Figure 3.

Direct Wall Mounting with Wall Mounting 

Bracket

The wall mounting bracket can be installed on masonry 

walls such as those constructed of brick or concrete, 

or to framed walls constructed of wood or steel framing 

sheathed with gypsum wallboard, drywall, wood, etc.  

The method used to mount the mounting bracket is dif-

ferent between masonry walls and framed walls.  Refer 

to the following sections for more detail on the method 

applicable to this installation.

•  The toggle-bolt anchors are provided to accomodate 

the required anchor points based on the appliance. 

Use of toggle bolt anchors requires drywall thick-

ness of minimum 1/2 in. and drilled holes size of 1/2 

in. diameter. 

• 

Insert the bolt through the front side of the mounting 

bracket and thread the toggle onto it from the rear of 

the bracket.  See Figure 4.   

• 

Fold the toggle wings flush against the bolt and push 

them through a drilled hole until the toggle wings 

expand open on the other side. See Figure 5.  

•  Pull back on the bolt and tighten. See Figure 5.   

 

Note:

  This product cannot be installed on a wall 

sheathed with drywall less than 1/2 in. thick, unless 

all six (6) anchor points in the mounting bracket 

align with structural framing members.

NOTICE:

  Minimum eight (8) screws and/or toggle bolt 

anchors are required for wall mounting. 

Figure 5  Installing Anchors in Hollow Wall 

Figure 4  Toggle Bolt Installation through Mounting Bracket

WARNING! Risk of Damage or Personal Injury! 

Al-

lowable pull-out and shear strength are 25% of ultimate 

values or less, as required by building authorities.

Summary of Contents for Scion Trinity SF-SCT43-MANTEL








Reviews: