background image

13

SimpliFire •  SF-ALL40-BK, SF-ALL48-BK, SF-ALL60-BK, SF-ALL84-BK Service Manual  •  2040-960  Rev. G  •  5/20

SimpliFire, a brand of Hearth & Home Technologies

7571 215

th

 Street West, Lakeville, MN 55044

www.hearthnhome.com

SimpliFire Troubleshooting Guide (continued)

Symptom

Possible Cause

Corrective Action

Ember bed does not light up

Ember bed is turned off

Refer to operation section of the user manual.

Loose wiring

Check wiring to ember bed LEDs.

Defective control board (PCB)

Replace control board (PCB).

Defective LED lights

Replace ember bed LED lights.

Fireplace turns on by itself

Defective control board (PCB)

Replace control board (PCB.)

Similar infrared signal from another 

remote causing unit to turn on (pre-

2019 manufactured units only)

Some TV remotes may cause the fireplace to turn on for 

appliances manufactured before 2019.  Replace control 

board (PCB).  

Excessive noise with heater on

Interference with fan blade

Inspect heater assembly and fan for obstructions or 

interference.  

Defective blower motor

Replace heater assembly.

Grinding or rubbing noise 

(when heater is off)

Rotisserie hitting or rubbing against 

internal components

Ensure rotisserie rod is straight and mounted properly 

and is spinning freely without spindles hitting other 

components.  If sound is coming from friction with the 

rotisserie bracket, apply grease to contact point

 

Summary of Contents for SF-ALL40-BK














Reviews: