background image

7

SimpliFire •  SF-ALL40-BK, SF-ALL48-BK, SF-ALL60-BK, SF-ALL84-BK Service Manual  •  2040-960  Rev. G  •  5/20

10.  Remove two (2) Phillips screws at the bottom of the 

       left and right side of the appliance opening.  See 

       Figure 15.

2 SCREW LOCATION

Screws at 

the bottom 

of the left  

and right side 

of appliance 

opening

SCREW LOCATION

11.   Remove Phillips screws at the top and bottom of  

        the flame screen.  See Figure 16.

12.

   Remove the flame screen.  

       

Note:

  Be sure to place on a flat surface with the

 

                    silk screen face-up. This is to prevent any  

                    distortion on the screen. 

13.  Remove the center screw located in the the center  

       of the Rotisseire.  Number of center supports may 

       vary.  See Figure 17.

CENTER SCREW LOCATION

14.   Pull the Rotisseire to the left to disengage it from  

        the motor, then remove the Rotisseire assembly.

Figure 15. Screw Location   

Figure 16.  Flame Screen Location   

Figure 17.  Rotisseire Screw Location

If replacing only the Rotisseire, 

install replacement 

part and reverse the installation steps.  

Be sure the flame screen is installed correctly with the 

flame silk screen to the outside and flames at the bottom 

of the appliance.

If replacing Motor 

continue to the next steps 15-18.

Rotisseire Installation

If replacing Flame LED Light Board continue to step 

19.

CAUTION!  Risks of Cuts!   

Rotisseire has sharp edges 

that can cut skin.  Always wear gloves when servicing the 

Rotisseire and/or Flame LED and/or Rotisseire Motor.

Summary of Contents for SF-ALL40-BK














Reviews: