background image

SimpliFire  • SF-ALLP50-BK, SF-ALLP60-BK, SF-ALLP72-BK  •  2044-980 Rev. C  •  10/19

  

8

D.  Location

Note:  

If this unit is installed in a bathroom, it must be 

protected by GFCI receptacle or circuit.  If receptacle is 

used it must be readily accessible.  This electrical ap-

pliance is not water tight.  To prevent electrical shock, it 

must be installed as to prevent water from entering unit.  It  

must be installed away from showers, tubs, or other water 

sources.  Never locate the appliance where it may fall into 

a bathtub or other water container. 

 

When choosing a location for your fireplace ensure that 

the following general rules are followed:  
•  For best results, install out of direct sunlight.  
•  Power supply service must be installed within  

proximity of electric fireplace prior to finishing to 

avoid reconstruction. 

•  Appliance should be mounted so the front glass 

panel is located outside the swing arc of adjacent 

door.

•  See Figure 3.2 and 3.3 to determine location of ap-

pliance installation.

E.  Clearance to Combustibles 

Minimum Clearance to Combustible Construction

  Sides.......................0 in.
  Floor........................0 in.
  Top..........................0 in.
  Back........................0 in.
  Front..................... 36 in.
  Mantel...................5/8 in.
   

See Figure 3.2.  

F.  Electrical Supply Circuit Requirements

Plan the location of the appliance so that it will have ad-

equate electric power.  A 15 AMP, 120VAC/60Hz circuit 

is required.  Additional appliances on the same circuit as 

this appliance may exceed the current rating of that cir-

cuit.  A dedicated circuit is not required, but is strongly 

recommended to prevent circuit breaker trips or fuse 

failure.

min. 0 in.

min. 5/8 in.

Ceiling

Mantel

Floor

Wall

Outside 

swing arc 

of adjacent 

doors

min. 0 in.

min. 4 in.

Figure 3.2 Location and Clearances Requirements

ELECTRICAL

OUTLET

LOCATION

Figure 3.3 Electrical Outlet Location

Note:  

If mounting on a wall and using the supplied pow-

er cord, choose a location near an outlet so an extension 

cord is not required.  

WARNING! Risk of Fire! 

Keep electrical cords, drapery, 

furnishings or other combustibles at least 3 ft. (0.9 m) 

from the front of the electric fireplace, and away from the 

sides or rear.

24 in. 

MAX

4 in.

MIN.

UNLIMITED

TRIM RING

Maximum Combustible and

Non-Combustible Mantel 

Projections. 

Summary of Contents for SF-ALLP50-BK





















Reviews: