background image

1

SimpliFire •  SF-SCT43-BK, SF-SCT55-BK Service Manual  •  2043-960  •  7/20

SERVICE MANUAL

Glass Front, Heater, Control Board, LED Spotlight, Ember Bed Cover, Glass Side Panels, Glass Screen 

Panel, Remote Receiver, Flame Screen, Rotisserie, Rotisserie Motors, Flame and Ember LEDs,

Model: SF-SCT43-BK, SF-SCT55-BK

- Instructions -

CAUTION! Risk of Cuts, Abrasions or Flying Debris. 

Wear protective gloves and safety glasses during 

installation and service. Sheet metal edges are sharp.

Leave this manual with party responsible for use 

and operation.

NOTICE!  DO NOT discard this manual. 

Important service 

and maintenance instructions included.

NOTICE!  DO NOT discard any hardware while 

servicing. 

It may be reused.

WARNING! Risk of Shock! 

Always turn off the circuit 

breaker before moving or servicing.  

Tools and Supplies Needed

Before beginning the installation be sure that the following 

tools and building supplies are available.

Needle-nose pliers 
Gloves
Magnetic Phillips screwdriver 
Safety glasses 
Drill  
Flat blade screwdriver

CAUTION!  Two adults recommended for the removal 

or installation of glass front.  

Use caution when han-

dling glass. Failure to do so could result in personal injury 

or property damage.

WARNING!  Risk of Personal Injury or Property Dam-

age! 

Failure to follow instructions below may result in 

damage to the equipment and / or may expose the user 

to the risk of fire, serious injury, illness or death.

Glass Front Replacement

 

1.    Remove the two (2) thumb screws and brackets 

       located on the inner upper corners of the appliance  

       opening. See Figure 1.
2.    Tilt the glass away from the appliance and lift out of 

       the bottom glass channel. 
3.    Set the bottom edge of glass into the glass channel  

       and tip back into the appliance until it rests against  

       the glass stops. 
4.    Re-install the glass brackets and thumb screws.

 

Figure 1.  Remove Glass Front

THUMB SCREW

THUMB SCREW

Summary of Contents for SF-SCT43-BK









Reviews: