background image

9

SimpliFire  •  SF-WMS38-BK  •  2040-911 Rev. E  •  12/15

  

Figure 4.6 Installing Anchors in Hollow Wall 

Figure 4.4  3/16 Toggle-Bolt Anchor

•  Four 3/16 toggle-bolt anchors are provided to ac-

commodate the four required mounting points. Use 

of toggle bolt anchors requires drywall thickness of 

minimum 1/2 in. 

•  Insert the bolt through the front side of the mounting 

bracket and thread the toggle onto it from the rear of 

the bracket.  See Figure 4.5.   

• 

Fold the toggle wings flush against the bolt and push 

them through a drilled hole until they expand open 

on the other side. See Figure 4.6.  

•  Pull back on the bolt and tighten. See Figure 4.4.   

 

Note:

  This product cannot be installed on a wall 

sheathed with drywall less than 1/2 in. thick, unless 

all four mounting points in the mounting bracket 

align with structural framing members. 

WARNING! Risk of Damage or Personal Injury! Al-

lowable pull-out and shear strength are 25% of ultimate 

values or less, as required by building authorities.

Framed  Wall

•  For each of the marked mounting point locations, 

determine which points align with a structural fram-

ing member.   

•  At the points where a wood or metal framing mem-

ber exists, the 5 x 40 screw can be installed directly 

into that structural member.  See Figure 4.3. 

•  Every mounting point that does not align with a 

structural framing member, a wall board toggle-bolt 

anchor must be used. See Figure 4.4.

Figure 4.5  Toggle Bolt Installation through Mounting Bracket

C.  Appliance Installation 

• 

  With the firebox at an angle, align the slots in the back 

of the firebox over the hooks on the bottom of the wall 

bracket.  Pull the appliance down to ensure that the 

hooks are fully engaged.  See Figure 4.7.A.

• 

   Carefully press the top of the firebox against the wall 

mount bracket sliding the top edge over the wall mount 

bracket tabs.  See Figure 4.7.B.

•    Secure the appliance to the bracket with two thumb 

screws.  See Figure 4.7.B.

1

2

3

Secure with thumb  

screw on each side of 

appliance.

Figure 4.7 Attaching Fireplace to Bracket

Mounting 

Hooks Point Up

A

B

Summary of Contents for SF-WMS38-BK















Reviews: