Getting Started DKIT-05
Landscape-Outdoor Lighting Kit
Simply Automated, Incorporated
6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA
Technical Support:
www.simply-automated.com
or
800-630-9234
452-0001-0005WEB Rev. B Revised: September 22, 2011
9
(indicator lit) and the load is connected to the bottom receptacle of the relay module (not the front receptacle).
Also, check that the load’s (transformer’s) ON/OFF switch is in the ON position. Make sure the Network ID
250, per Section 3.c. If the transformer load is still not turning ON/OFF, move the Scheduler-Timer to the
transformer. Plug the Scheduler-Timer into the front receptacle of the relay module and repeat test steps outlined
above. With the cursor on event number “02)” the relay module should turn ON/OFF when pressing the Enter
# is
utton. You should be able to hear the relay module click ON and OFF. For further assistance see Section 6.
N”
15 minutes and OFF at midnight (12:00AM); when the sch
3)
. With the scheduler plugged into power, the Idle screen should be
isplayed:
•
d played.
Se
nt
.
•
um er field, press the Dow button
•
ID number field. Press the Up button to
scroll up to Scene Link number 019.
•
ll
event to run every
day, or change any day to a lower case if you do not want this event to run on that day.
•
Up
to “R” run, so the event will be active in the
normal runtime schedule mode.
•
minutes) of the ON time field. Press the Up button to scroll the ON time to dusk mi
•
time
press the Up (or Down) button to scroll the OFF time to
midnight “12:00A”.
•
press the Up (or Down) button to set the Event type to scene link activator “LA”.
button saves the changes made. Pressing Menu button will exit back to the
enu without saving changes.
e Event number (e.g. “03”) will test the event
y toggling between ON and OFF each time Enter
is pressed.
b
Section 4.e. Setting Event 03) for a Group (SCENE) of Modules
The relay modules #018 and #019 (as labeled on the back of the units) are pre-configured to operate with the
optional 4 and 8 button scene controller accessories (see Section 5 for more details). In this example the “All O
lighting scene link ID #019 (associate with button 3 of the scene controllers) will be used to by the scheduler to
turn ON both modules at dusk (sunset) minus
eduler is
in the regular runtime (RUN) schedule mode.
Set Event 0
d
From the Idle screen press the Down button. The first event will be is
select “1)
t Eve ” and press Enter
Or, press the Menu button to
The scheduler will show the first event “01)”. With the cursor in the event
01)018 SMTWTFS R
DSK+00 11:00P D0
n
b
n
two times to scroll to the third event “03)”.
With the cursor highlighting the event number “03)", press the Right button to
move the cursor over to the Scene Link
Press the Right button to move the cursor over to the days of the week field.
Pressing the Up or Down button on any of the days of the week will change the capital letter to a lower case
letter. Capital letter indicates an ON day; lower case indicates an OFF day for this third “03)” event. Leave a
the initials of the days of the week (Sunday through Saturday) capitalized if you want the
03)--- SMTWTFS R
12:00A 12:00A LA
Press the Right button to move the cursor to the event mode field. Using the
or Down buttons set event mode
03)019 SMTWTFS R
12:00A 12:00A LA
Press the Right button to move the cursor to the hours segment (not the
nus 15 minutes “DSK-15”.
Press the Right button to move the cursor to the hours segment of the OFF
field. If necessary,
03)019 SMTWTFS R
DSK-15 12:00A LA
Press the Right button to move the cursor to the Event Type field. If necessary,
03)019 SMTWTFS R
DSK-15 12:00A LA
•
Press the Enter button to save the event. You’re done setting the third event.
Helpful Hint: Pressing the Enter
M
Helpful Hint: Pressing the Enter
button when the cursor is on th
b