background image

7

PARTS LIST FOR DVS-5, DVH-3 & DVRS-5 WET/DRY VACUUM

SERIAL “A”

 Fig. 

Part 

  No. 

No. 

Description

  1. 

MV-08  Electric Cord

   

MV-09  Electric Cord (Remote Start Model)

  2. 

MV-02  Motor Cover

  3. 

MV-44  #6 x 2 Screw (4)*

  4. 

MV-03  Brass Agitator Rod Cover

  5. 

MV-36  On/Off Switch

  6. 

MV-01  Motor Cover (Remote Start Model)

  7. 

MV-39  Remote Start Outlet (Remote Start Model)

  8. 

MV-37  On/Off Switch (Remote Start Model)

  9. 

MV-32  Remote Start PCB (Remote Start Model)

 10. 

MV-07  Motor

 11. 

MV-42  #8 x 3/8 Black Pan Head Screws (8)*

 12. 

MV-04  Vac Lid

 13. 

MV-06  Lid Clamp (3)*

 14. 

MV-33  Spring (Wet/Dry Vacuum)

 15. 

MV-05  Cage (Wet/Dry Vacuum)

 16. 

MV-34  Silver Shoulder Screw (Wet/Dry Vacuum)

 17. 

MV-19  Secondary Filter (Wet/Dry Vacuum)

 18. 

MV-24  Filter Support With Agitator Rod (Wet/Dry Vacuum)

 19. 

MV-46  7" Hose Clamp(Wet/Dry Vacuum)

 20. 

MV-18  Primary Filter (Wet/Dry Vacuum)

 21. 

MV-20  Crosspiece (HEPA Vacuum)

 22. 

MV-21  HEPA Filter (HEPA Vacuum)

 23. 

MV-22  HEPA Filter Filter Cover Support (HEPA Vacuum)

 24. 

MV-41  Rubber Washer (HEPA Vacuum)

 25. 

MV-48  Wing Nut (HEPA Vacuum)

 26. 

MV-23  HEPA Filter Cover (HEPA Vacuum)

 27. 

MV-45  Lid Clamp

   

MV-47  Band Clamp (HEPA Vacuum)

 28. 

MV-29  Intermediate Cover

 29. 

MV-31  Float Ball

 30. 

MV-43  Screw (3)*

 31. 

MV-30  Float Ball Basket

 32. 

MV-17  Accessory Tray

 33. 

MV-10  Barrel

 34. 

MV-11  Barrel Intake Port

 35. 

MV-13  “O” Ring

 36. 

MV-12  Drain Cap

 37. 

MV-14  Front Legs (2)*

 38. 

MV-15  Back Legs (2)*

 39. 

MV-16  Casters and Stem (4)*

 40. 

MV-28  12' x 1 1/2" Vacuum Hose

 41. 

MV-27  Extension Wand

 42. 

MV-26  Crevice Tool

 43. 

MV-25  Floor Tool

Not Shown:

   

MV-35  Red Connector

   

MV-36  Switch

   

MV-38  Cord Relief

   

MV-40  Hex Head Screw .5"

*Order Quantity As Required

FURNISH CATALOG, SERIAL, AND MODEL NUMBER 

WHEN ORDERING PARTS

Summary of Contents for DVH-3










Reviews: