Setting up date/time
(Service Mode)
The value to change is blinking.
Right/Left
arrows
moves the cursor between year, month, day etc.
Up/Down
arrows increases/decreases the value.
Press
Enter
when done. Press “
C”
key to exit
without modifications.
Run indication relay output/Operational mode
(Service Mode)
There are 15 possible functions for the run
indication relay output DO4. Change mode with
Right / Left
arrow
:
OPEN AT FUNC.TEST – relay opens as long as at
least one module is performing a function test.
OPEN AT NIGHT – relay opens if system is in night
mode.
NIGHT+FUNC.TEST – relay opens if system is in
night mode or a function test is performed.
OPEN AT SUM ALARM – relay opens if there is
any damper error or communication error in the
system.
SFUNCTEST – relay opens if there is
any damper error or communication error in the
system or a function test is performed.
SNIGHT - relay opens if there is any
damper error or communication error or if system
is in night mode.
SUM+NIGHT+F.TEST – relay opens if there is any
damper or communication error, or if the system is
in night mode or a function test is being performed.
OPEN AT FIRE – relay opens in case of fire alarm.
FIRE+FUNC.TEST – relay opens in case of a fire
alarm or a function test is being performed.
FIRE+NIGHT – relay opens if case of a fire alarm
or if system is in night mode.
FIRE+NIGHT+F.TEST - relay opens in case of a
fire alarm, or if the system is in night mode or a
function test is being performed.
FIRE+SUMALARM - relay opens if there is a fire
alarm, a damper error or a communication error in
the system.
FIRE+SUM+F.TEST - relay opens in case of a fire
alarm or if there is a damper or communication
error in the system or a function test is being per-
formed.
FIRE+SUM+NIGHT - relay opens in case of a fire
alarm, a damper or communication error in the
system or if the system is in night mode.
FIRE+SUM+NIGHT+FT - relay opens in case of a
fire alarm, a damper or communication error in the
system, or if system is in night mode or a function
test is being performed.
Module addressing
(Service Mode)
This setup menu is used for addressing damper
control modules. Every module in the system
requires a unique address. The address consists of
a
Group
address and a
Module
address. The
Group
address is either zero which is used to
address the first 1-59 damper modules or it could
be 61, 62 or 63 that defines three possible
addressing subgroups
(only available if SMOKE
EDIT is used)
. Each group can handle up to 59
damper modules (less if other modules are used
as well).
Please note that if digital I/O-modules are used, for
example S27, they should be addressed from
address 59 and downwards. This means that
correspondingly fewer damper modules can be
installed on group zero.
All modules are at
Group
address 0 and
Module
address 1 when they are delivered from factory.
Press
Enter
to select Module addressing menu.
The modules should be addressed in the interval
1-59, that's why the addressing starts at 1. If
another start address is desired, just change it by
pressing the
Up/Down
arrows to increase/decrease
and
Left/Right
arrows to move between
Group
and
Module
address.
When
Enter
is pressed the MIDI SMOKE 2 starts
to send addressing commands. All damper control
modules LEDs will start to flash (3 fast on/off). By
pressing the test button on a module it accepts the
address sent by MIDI SMOKE 2. The address in
the display now increments to the next address
and the next module in order can be addressed.
Note that no automatic wrap occurs to next
Group
address when
Module
address 59 has been
passed. It will stay at address 59. If sub-buses are
used, restart the command and increase the
Group
address to the desired
Group
address (61,
62, 63). Please note that pressing
Down
arrow is a
quick way to reach the high
Group
address
numbers (0->63->62->61). Adjust the
Module
address to the desired start address before
pressing
Enter
to start the transmission of the
addressing commands.
Apply a distinct press on the buttons to avoid
double-activations which otherwise will result
in an address increment and a wrong address
Profcon AB
Page 9
www.smokecontrol.net
2018-02-20 16:30
WEDNESDAY
SETUP RUN IND.
OPEN ON ERROR
ENTER = START
GROUP:0 ADDR:1
MODULE ADDRESSING
