background image

62 07 687 D3530

D3530

.

201.01.06

.

02 07.2011

23

Sirona Dental Systems GmbH

5

 

Care and cleaning instructions for the practice team

Operating Instructions LEDview / LEDview S

5.1

 

Basics

båÖäáëÜ

5

Care and cleaning instructions for the 

practice team

Care and cleaning instructions for the practice team

5.1

Basics

Basics

To maintain the value and safe functioning of your operating light, it is 

necessary to have it cared for, cleaned and disinfected by the practice 

team regularly. This will minimize the risk of contamination for patients 

and users and ensure proper functioning.
The national requirements and recommendations for hygiene and 

disinfection must be observed, e.g. Robert Koch-Institut (RKI), American 

Dental Association (ADA), Centers for Disease Control and Prevention 

(CDC), etc.
➢ Clean and disinfect the lamp components after each patient.

5.2

Care and cleaning agents

Care and cleaning agents

CAUTION: Approved care and cleaning agents

The list of agents forms part of the folder

You will find a list of all agents approved at the time of delivery in the 

documentation folder supplied with your treatment center.

Care and cleaning agents, with REF number

A continuously updated list of approved agents can be downloaded from 

the Internet at the address 

"www.sirona.com". In the navigation bar, go to 

the menu items 

"SERVICE" / "Care and cleaning" and then open the 

document 

"Care and cleaning agents".

If you do not have any access to the Internet, please contact your dental 

depot to order the list.
REF 59 70 905

CAUTION

Care and cleaning intervals
The time intervals specified for disinfection, care and cleaning are 

reference values.
➢ Please adapt the time intervals to suit your personal method of 

working and your national requirements.

NOTICE 

Approved care and cleaning agents
Use only care and cleaning agents which have been approved by 

Sirona!

Summary of Contents for LEDview



























Reviews: