background image

GENERAL HAZARD WARNING:

Failure to comply with the precautions and 
instructions provided with this heater can 
result in death, serious bodily injury and 
property loss or damage from hazards of 
fire, explosion, burn, asphyxiation, carbon 
monoxide poisoning, and/or electrical 
shock.

Only persons who can understand and 
follow the instructions should use or service 
this heater.

If you need assistance or heater information 
such as an instruction manual, label, etc. 
contact the manufacturer.

WARNING:

Fire, burn, inhalation, and explosion 
hazard. Keep solid combustibles, such as 
building materials, paper, or cardboard, 
a safe distance away from the heater as 
recommended by the instructions. Never 
use the heater in spaces which do or may 
contain volatile or airborne combustibles, 
or products such as gasoline, solvents, 
paint thinner, dust particles or unknown 
chemicals.

FOR YOUR SAFETY:

The use and storage of gasoline or other flammable vapors and liquids in the vicinity 
of this appliance is hazardous.

WARNING:

Not for home or recreational vehicle use.

WARNING:

Cancer and reproductive harm. 

 See  www.P65Warnings.ca.gov.

3

GENERAL HAZARDS

Summary of Contents for Sleeptight 800










































Reviews: