background image

チコーエアーテック株式会社

Copyright CHIKO AIRTEC CO., LTD. 2009

15

6

保守・点検

Maintenance and Inspection

6.1

保守点検時の注意事項

Cautions on maintenance and inspection

6.2

フィルタの交換時期について

Filter replacement timing

フィルタ目詰ランプが点灯しましたら、1次フィルタを交換してください。
また、1次フィルタを交換しても、目詰まりランプが消えないときには、2次フィルタを交換してください。

If the filter replacement indicator lamp does not turn OFF even after replacement of the primary filter (filter
bag), replace the secondary (main) filter.

1次フィルタ(フィルタバッグ)の交換

Replacement of primary filter (filter bag)

点検時は必ず電源を切り、コンセントからプラグを抜いて、電路遮断を
行ってください。

Make sure to turn OFF the main power, and disconnect the power plug
from the electrical outlet to cut off the electricity before starting
inspection.

摩耗や破損したフィルタをそのまま使用すると、吸込んだ粉塵を大気に再飛
散させ、電気部品の損傷となります。
機械の故障、事故を未然に防ぎ、
末永くご使用頂けますよう、点検、手入れは必ず行ってください。

Using a worn or damaged filter will release sucked dust to the
atmosphere, and damage electrical parts.
Make sure to inspect and maintain, to prevent failures and accidents in
the product and to use the product for a long time.

フィルタの交換時は、電源を切り、
コンセントからプラグを抜いて、電路遮断を行ってください。

Make sure to turn OFF the power, and disconnect the power plug from
the electrical outlet before starting inspection.

パッチン錠

Snap lock

①フィルタケースのパッチン錠を外します

Release the snap locks of the filter case

②フィルタケースの円筒パイプにフィルタ紙パッキン部を差し込んでいますので、下に向かって軽く押さえて、取外します。

The filter paper packing of the primary filter is inserted into the cylindrical pipe of the filter case.
Lightly push down the filter paper packing to remove it.

③新しいバッグは、フィルタ紙パッキン部の矢印を合わせて、取り付けて下さい。

Attach a new filter bag while aligning the arrow of the filter paper packing.

Summary of Contents for SKV-250AT-ACC























Reviews: