background image

チコーエアーテック株式会社

Copyright CHIKO AIRTEC CO., LTD. 2009

5

1.4

運転

Operation

運転中に移動させないで下さい。

Do not move it during the operation.

停電した時には、電源を切って下さい。復旧時に、けが・装置破損の原因になります。

Turn OFF the power when an instantaneous power interruption occurs.
Otherwise, injury or product damage may be caused when the product recovers.

フィルタを取り外したり、目詰まりや破損した状態で運転すると、
ブロア内への異物が混入して、故障の原因となります。 正しくフィルタを取り付けてご使用ください。

Operation without filter or with a clogged and damaged filter may cause trouble, because foreign substances
enter the blower. Install the filter properly before operating the machine.

1.5

修理・分解・改造

Repair, disassembly and modification

本体を分解・改造しないで下さい。感電・けがの原因になります。内部の点検や修理はお買い上げになった販売店に連
絡して下さい。

Do not disassemble or modify the machine.
Disassembly and modification may cause an electrical shock and injury.
Contact your dealer for internal inspection and repair.

1.6

廃棄

Disposal

産業廃棄物として適切に処分してください。

Dispose of the product properly as industrial waste.

2

製品到着時の確認

Confirmation and Preparation at Arrival

開梱されましたら、各部の不足部品がないかご確認下さい。
万一、運送途中での破損・部品不足などがございましたら、すぐにご連絡下さい。

After unpacking, make sure that all parts are provided.
Contact our company immediately if parts are damaged during transportation or not provided.

本体

Main Body

製品ネームプレートは本体に貼っていますので、ご確認下さい

Confirm the nameplate.

フィルタ(本体にセットされています)

Filter

set in the machine

SKV-250AT-ACC

SKV-450AT-ACC(-V1)

1

次フィルタ

Primary filter

FB-40

FB-700-22

2

次フィルタ

Secondary filter

CHF-3030-30

CHF-4040-40

メインフィルタ

Main filter

CS-300-150

CS-300-200

粒状活性炭

Active carbon

YAC-8000(8kg)

YAC-12500

12.5

kg)

電源ケーブル(付属)とリモートケーブル(別売)
Power cable and Remote cable(option)

電源ケーブル

Power cable

(3m) ×1

※ ケーブルは地域によって異なります。
※ The cable is different in each region.

リモートケーブル(別売) MT-173-8

Remote cable(option)

(3m) ×1

抜け防止の設計となっております。くぼみを下にし、しっかりと差し込んで
下さい。

(ピンの位置を必ず確認してください)

The remote cable is so designed as to be prevented from falling off.
Insert it securely with its dent facing downward.
(Make sure to confirm pin positions.)

100-110V

200V

国内

Japan

200V

海外

Other than Japan

Summary of Contents for SKV-250AT-ACC























Reviews: