11
-
it takes a short time for the hammer mechanism to
reach full impact power
-
best hammer drilling results can be obtained by only a
slight pressure on the tool; drilling performance will not
improve by applying more pressure on the tool
•
Battery protection
Switches off the tool or prevents the tool from being
switched on, when
-
the load is too high
-
the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
-
the lithium-ion battery is nearly empty (to protect
against deep discharge)
!
do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
•
LED-light E
r
-
LED-light E automatically lights on when activating
switch A
2
•
Holding and guiding the tool
t
! while working, always hold the tool at the grey-
coloured grip area(s)
-
keep ventilation slots F
2
uncovered
-
do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
•
Use the appropriate bits
y
! only use sharp bits
•
For drilling with non SDS drill bits in wood, metal and
plastic, use an adapter
(not standard included)
u
! clean and lightly lubricate the SDS+ accessory
before insertion
-
pull back locking sleeve C
2
and insert adapter
in SDS+ chuck while turning and pushing it until it
engages; the adapter locks in position automatically
-
pull adapter to check whether is it locked correctly
-
set switch D
2
to normal drilling (only activate when
tool is switched off and the switch is locked)
•
When drilling ferrous metals
-
pre-drill a smaller hole, when a large hole is required
-
lubricate drill bit occasionally with oil
•
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
•
Splinterfree drilling in wood
i
•
Dustfree drilling in walls
o
•
Dustfree drilling in ceilings
p
•
Drilling in tiles without skidding
a
•
For more information see www.skil.com
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Always keep tool clean (especially ventilation slots F
2
)
! remove battery from tool before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-
send the tool
undismantled
together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Only use the following batteries and chargers with
this tool
-
SKIL battery: BR1*31****
-
SKIL charger: CR1*31****
•
Do not use the battery when damaged; it should be
replaced
•
Do not disassemble the battery
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
-
when charging 4...40°C
-
during operation –20...+50°C
-
during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3
Read the instruction manual before use
4
Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5
Store tool/charger/battery in locations where temperature
will not exceed 50°C
6
Do not dispose of electric tools and batteries together
with household waste material
USE
•
Combined switch for on/off and speed control A
2
8
9
-
control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery
2
•
Battery level indicator
7
-
press the battery level indicator button H to show the
current battery level.
•
Changing direction of rotation
q
-
when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•
Changing bits
w
! clean and lightly lubricate the SDS+ accessory
before insertion
-
pull back locking sleeve C and insert accessory
in SDS+ chuck while turning and pushing it until it
engages; the accessory locks in position automatically
-
pull accessory to check that it is locked correctly
-
remove accessory by pulling back locking sleeve C
! the SDS+ accessory requires freedom of
movement which causes eccentricity when tool
is off-load; however, the accessory automatically
centres itself during operation without affecting
drilling precision
! when using hex bits, make sure that these hex bits
are at least 75 mm long, or otherwise use shorter
hex bits with hex adapter G
! do not use bits with a damaged shank
•
Selecting operating mode
e
1 = normal drilling/screwdriving
2 = hammer drilling
! select operating mode only when tool is switched
off and the switch is locked
-
the hammer mechanism is activated by applying a
slight pressure on the tool when the drill bit is in contact
with the workpiece
Summary of Contents for 3810
