7
• Holding and guiding the tool
7
! while working, always hold the tool at the
grey-coloured grip area(s)
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots F
2
uncovered
APPLICATION ADVICE
• Move the tool in straight movements in line with the grain
- for sanding bare wood surfaces
- for extra fine finishing
• Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
coarse -
for removing paint; for sanding of extremely
rough wood
medium -
for sanding of rough or plain wood
fine -
for smoothing of wood; for finishing of bare
wood; for smoothing surfaces with old paint
• Use different grit sizes when the working surface is
rough:
- start sanding with coarse or medium grit
- finish with fine grit
• For more tips see www.skil.com
mAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots F
2
)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool
undismantled
together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONmENT
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol
8
will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORmITY
• We declare under our sole responsibility that the product
described under “Technical data” is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
•
Technical file at
: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
¹ÊÁÂÆιƼ½ÊÇǾ¼½Æ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ
Ĺ¾ ÁÂÿʹ¹¾
ÈÈÊÇιĹƹ¿½Ê
07.08.2013
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 85 dB(A) and the sound
power level 96 dB(A) (standard deviation: 3 dB), and the
vibration 12.8 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase
the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce
the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Ponceuse vibrante
7361/7366
INTRODUCTION
• Cet outil sert au ponçage et au polissage à sec du bois,
des surfaces peintes, du plastique et du mastic
• Cet outil n’est conçu pour un usage professionnel
• Lisez et conservez ce manuel d’instruction
3
CARACTERISTIQUES TECHNIQUES
1
ELEmENTS DE L’OUTIL
2
A
Interrupteur marche/arrêt
B
Réservoir à poussière
C
Bouton de retrait du réservoir à poussière
D
Contrôle de pression (7366)
Summary of Contents for 7003
Page 3: ...3 4 B C B 5 ...
Page 4: ...4 4 3 2 1 6 8 7 ACCESSORIES www skil com ...
Page 101: ...101 4 3 2 1 6 8 7 ت ا ق ح ل مل ا www skil com امللحقات ...
Page 102: ...102 4 B C B 5 ...
