INTRODUCTION
●
This tool is intended for dry sanding with high removal
performance of wood, plastic, metal, filler and painted
surfaces
TECHNICAL SPECIFICATIONS
1
SAFETY
●
Read and save this instruction manual (pay special
attention to the safety instructions at the back)
●
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
●
Always keep the cord away from moving parts of the tool
●
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
●
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
●
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
●
SKIL can assure flawless functioning of the tool only
when original accessories are used
●
This tool should not be used by people under the age of
16 years
●
The noise level when working can exceed 85 dB(A);
wear ear protection
●
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
●
Never use tool when cord is damaged; have it replaced
by a qualified person
●
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
●
This tool is not suitable for wet sanding
●
Do not sand material containing asbestos
●
When sanding metal, sparks are generated; do not use
dustbag and keep other persons and combustible
material from work area
●
Do not touch the running sanding belt
●
Do not continue to use worn, torn or heavily clogged
sanding belts
●
Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
●
Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials to
be worked on
●
Always direct the cord to the rear away from the tool
●
Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
●
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
●
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
●
Belt CLIC System
- ensures quick-changing of sanding belt
- centers sanding belt automatically
●
Quick-changing of sanding belts
2
! disconnect the plug
- lift lever A
- remove sanding belt
- insert new belt with arrows printed at inner side of belt
pointing in same direction as arrow B on tool
- push lever back
! change sanding belts in time
! never fold sanding belts
●
Automatic belt centering
- centers belt automatically when switching on tool
- keeps belt centered while sanding
In case belt runs off tool (mostly caused by inferior belt
quality), you should
- switch on the tool
- adjust screw C
3
till the sanding belt is running in
line with the flat side of the tool
- use new belt, if belt still runs off tool
●
Removing and mounting dustbag
3
- empty dustbag regularly for optimal dust pick-up
performance
! do not use dustbag when sanding metal
●
On/off switch
- switch on/off the tool by pulling/releasing trigger D
3
! before the sanding surface reaches the
workpiece, you should switch on the tool
! before switching off the tool, you should lift it
from the workpiece
●
Switch lock
3
- pull trigger D
- press knob E with your thumb
- release the trigger
- unlock the switch by pulling again trigger D and then
releasing it
●
Holding and guiding the tool
4
- guide the tool parallel to the working surface
! do not apply pressure on the tool; let the sanding
surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots F uncovered
APPLICATION ADVICE
●
For sanding bare wood surfaces move the tool in
straight movements in line with the grain
●
For sanding all other surfaces move the tool in oval
movements over the material
●
For stationary use mount tool on workbench or vice
5
●
Never use the same sanding belt for wood and metal
●
Recommended sanding sheet grits:
coarse
- for removing paint;
for sanding of extremely rough wood
medium - for sanding of rough or plain wood
fine
- for smoothing of wood;
for finishing of bare wood;
for smoothing surfaces with old paint
GB
4
XP SKIL 7600/7675 28-05-2002 12:56 Pagina 4
