INTRODUCTION
●
This tool is intended for grinding, cutting and deburring
metal and stone materials without the use of water; with
the appropriate accessories the tool can also be used for
brushing and sanding
TECHNICAL SPECIFICATIONS
1
SAFETY
GENERAL
●
Read and save this instruction manual
and the
enclosed safety instructions
2
●
Only use this tool for dry grinding/cutting
●
Only use the flanges which are supplied with this tool
●
This tool should not be used by people under the age of
16 years
●
Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
●
Use the original SKIL accessories which can be obtained
from your SKIL dealer
●
For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
●
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
●
Do not use damaged, deformed or vibrating grinding/
cutting discs
●
Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
●
Protect accessories from impact, shock and grease
●
Do not use a grinding/cutting disc that is larger than the
maximum recommended size
●
Only use grinding/cutting discs with a hole diameter
which fits mounting flange D
6
without play; never use
reducors or adaptors to fit large-hole grinding/cutting
discs
●
Never use grinding/cutting discs with a threaded hole, of
which the thread is not long enough to accept the spindle
length of the tool
●
Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
●
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
●
Only use an extension cord which is intended for outdour
use and equipped with a splashproof coupling-socket
BEFORE USE
●
Before using the tool for the first time, it is recommended
to receive practical information
●
Do not work with materials containing asbestos
●
Be careful of hidden electrical wires or gas- and water
pipes; check the work area, for instance with a metal
detector
●
Be careful when cutting groves, especially in supporting
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances, so before beginning work,
consult with the responsible structural engineer, architect
or construction supervisor)
●
Clamp the workpiece in case it does not remain
stationary from its own weight
●
Do not clamp the tool in a vice
●
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
●
Wear protective glasses and gloves, hearing protection
3
, a dust mask, and sturdy shoes; when necessary, also
wear an apron
●
Always mount auxiliary handle A
6
and protective guard
B
6
; never use the tool without them
●
Be sure tool is switched off when plugging in
DURING USE
●
Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
●
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug;
never use the tool with a damaged cord
●
Push spindle-lock button G
6
only when spindle C
6
is
at a standstill
●
Keep hands away from rotating accessories
●
When grinding metal, sparks are generated; keep other
persons and combustible material from work area
●
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
●
In case the cutting disc is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
●
In case of current interruption or when the plug is
accidentally pulled out, unlock the on/off switch
immediately and put it in the OFF-position in order to
prevent uncontrolled restarting
●
Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
●
Before you put down the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
●
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
●
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
●
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
●
Mount auxiliary handle A
4
●
Mount protective guard B
5
! ensure that the closed side of the protective guard
always points to the operator
GB
5
XP SKIL 9370/9375/9380/9385.2 17-06-2003 10:36 Pagina 5
