General information
Read and observe on page 228 first.
For your own safety and the safety of your passengers, the following instruc-
tions must be observed before carrying out a wheel repair on the road.
Switch on the hazard warning lights system.
Place the warning triangle at the prescribed distance.
Park the vehicle as far away as possible from the flowing traffic.
Choose a location with a flat, solid surface.
Have
all the occupants get out.
The passengers should not stand on the
road (instead they should remain behind a crash barrier, for instance) while
the wheel is being changed.
The breakdown kit must not be used under the following circumstances.
▶
The rim is damaged.
▶
The outside temperature is below -20 ° C.
▶
The cut or puncture is larger than 4 mm.
▶
The tyre wall is damaged.
▶
After the expiration date (see inflation bottle).
Preparations for using the breakdown kit
Read and observe on page 228 first.
The following preparatory work must be carried out before using the puncture
repair kit.
›
Switch off the engine.
›
For vehicles with
manual transmission
engage
1st gear
.
›
On vehicles with
automatic transmission
place the selector lever in the
P
po-
sition.
›
The parking brake switch.
›
Check that you can carry out the repairs with the breakdown kit
» page 228
.
›
Uncouple any trailers.
›
Remove the breakdown kit from the boot.
›
Stick the sticker
1
» Fig. 248
on page 228
on the dashboard in the driver's
field of view.
›
Unscrew the valve cap.
›
Use the valve remover
2
to unscrew the valve core and place it on a clean
surface (rag, paper, etc.).
Sealing and inflating the tyre
Read and observe on page 228 first.
Sealing
›
Forcefully shake the tyre inflation bottle
10
» Fig. 248
on page 228
back and
forth several times.
›
Firmly screw the inflation hose
3
onto the tyre inflater bottle
10
. The film on
the cap is pierced automatically.
›
Remove the plug from the inflation hose
3
and plug the open end fully onto
the tyre valve.
›
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
›
Remove the filler plug from the tyre valve.
›
Screw the valve core back into the tyre valve using the valve remover
2
.
Inflating
›
Screw the air compressor tyre inflation hose
7
» Fig. 248
on page 228
firmly
onto the tyre valve.
›
For vehicles with
manual transmission
the lever into the neutral position.
›
On vehicles with
automatic transmission
place the selector lever in the
P
po-
sition.
›
Start the engine and run it in idle.
›
Plug the connector
6
into 12 volt socket
» page 100
.
›
Switch on the air compressor with the ON and OFF switch
9
.
›
Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved.
Maximum run time of 8 minutes
»
.
›
Switch off the air compressor.
›
If you cannot reach an air pressure of 2.0 - 2.5 bar, unscrew the tyre inflation
hose
7
from the tyre valve.
›
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent
to “distribute” in the tyre.
›
Firmly screw the tyre inflation hose
7
back onto the tyre valve and repeat
the inflation process.
›
Switch off the air compressor.
›
Remove the tyre inflation hose
7
from the tyre valve.
Once a tyre inflation pressure of 2.0 - 2.5 bar is achieved, you can continue the
journey.
229
Emergency equipment and self-help
Summary of Contents for 2015 Superb
