BATTERY
INSTALLATION
x-blox assembly
Read and follow operating instructions.
1. Do not mix old and new batteries.
2. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Nickel-cadmium)
batteries.
3. Only batteries of the same or equivalent type as recommended are to be used.
4. Batteries are to be inserted with the correct polarity.
5. Exhausted batteries are to be removed from the product.
6. The supply terminals are not to be short-circuited.
7. Non-rechargeable batteries are not to be recharged.
8. Rechargeable batteries are to be removed from the product before being charged (if removable)
9. Rechargeable batteries are only to be charged under adult supervision.
10. Dispose of batteries safely.
11. Do not dispose of this product in a fire. The batteries inside may explode or leak.
12. Batteries should be changed by adults only.
CAUTION:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Effective signal range: 40 feet or 12 meters.
**This device and its antenna must not be co-located or operating in conjunction with any other antenna
or transmitter.
This Class B digital apparatus complies with Canadian ICES-003. Conforms to ASTM F963 standard.
Contents and color may vary slightly from these shown. Please retain packaging for future reference.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
PRECAUCIÓN:
Los cambios o modificaciones que se hagan a este aparato que no sean expresa-
mente aprobados por la parte responsable del cumplimiento podrían anular la autoridad del usuario
para operar el equipo.
OBSERVACIÓN: Este dispositivo ha sido probado y cumple con los límites para un dispositivo digital
de Clase B, de acuerdo con la Parte 15 de los reglamentos de la Comisión Federal de Comunicaciones
(FCC). Estos límites están diseñados para proporcionar una protección razonable contra interferencias
peligrosas en una instalación residencial. Este equipo genera, utiliza y puede irradiar energía de
radiofrecuencia y, si no se instala y se utiliza de acuerdo con las instrucciones, puede causar
interferencias en las comunicaciones de radio.
Sin embargo, no hay garantía de que no se produzcan interferencias en una instalación específica. Si
este equipo causa interferencias adversas en la recepción de radio o televisión, lo cual puede
comprobarse encendiéndolo y apagándolo, se recomienda al usuario que intente corregir la interferen-
cia mediante una o más de las siguientes medidas:
- Vuelva a orientar o a ubicar la antena receptora.
- Aumente la distancia de separación entre el equipo y el receptor.
- Conecte el equipo a una toma eléctrica que esté en un circuito que no sea en el que está conectado
el receptor.
- Consulte a su distribuidor o a un técnico de radio/televisión con experiencia para obtener ayuda.
Alcance operante de la señal: 40 pies o 12 metros.
** Este dispositivo y su antena no deben colocarse ni operarse junto con otra antena o transmisor.
Este aparato digital Clase B cumple con la norma ICES-003 de Canadá. El contenido y los colores
pueden ser ligeramente de los que se muestran. Cumple con la norma ASTM F963.
Guarde el empaque para futuras referencias.
GENERAL BATTERY INFORMATION
IMPORTANT
X-BLOX
BASE PLATE
HINGES
RISERS
TRACK
Hint:
Try to master a short jump prior
to setting up for longer jumps. Drivers
need to slow down at the correct time
in order to regularly complete the
jump successfully.
Riser plate slides
into the track grooves
STEP A
1. Unscrew battery door on handle
2. Remove battery door from handle
STEP B
1. Insert batteries as shown in diagram
2. Replace battery door on handle
phillips head
screwdriver
A
A
B
B
AA LR6 (1.5V
)
AA LR6 (1.5V
)
AA LR6 (1.5V
)
AA LR6 (1.5V
)
battery compartment
battery compartment (open)
1.5v (LR-44) batteries
battery cover
phillips head
screwdriver
NOTE:
Each controller
requires 4 AA/LR6
(1.5V) batteries
(not included)
NOTE:
Lap counter
requires 3 (LR-44)
(1.5V) batteries
(included)
DIGITAL LAP COUNTER