background image

Page 3 of 5 

4- Connect the short modular cord from [1&2 to Phone] on CK-1 to [LINE 1&2] on 
Phone. (Fig #3) 
 
5- Connect the short modular cord from [3&4 to Phone] on CK-1 to [LINE 3&4] on 
Phone. (Fig #3) 
 
6-  Connect the supplied audio cord to the AUDIO IN jack on the back of the CK-1 box. 
Connect the other end, to your audio source. Do NOT use the adapter that came with the 
audio cable unless the connector (RCA) NOT fit into your MP3 player. DO NOT  plug 
the audio adapter into the CK-1 box.  (Fig #3) 
 
7- Connect a MOD cord from Telephone Wall Jack 1&2 to [1&2 to Line] on CK-1. 
 
8- Connect a MOD cord from Telephone Wall Jack 3&4 to [3&4 to Line] on CK-1. 
 
9- Connect the POWER CUBE from the CK-1 box to 115VAC power. 
 

KX-TG2000 Installation Notes: 

The KX-TG2000 and KX-TG4000 are very similar. The following is a list of the 
differences in the installation process between the two phones. 
1- When you mount the "SENSOR BOARD" on the telephone, the "3" and "4"  on the 
SENSOR board will represent line 1 and 2 on the telephone. 
2-Connect the short modular cord from [3&4 to Phone] on the  CK-1 to [LINE 1&2] on 
the Phone. 
3- Connect a MOD cord from the Telephone Wall Jack 1&2 to [3&4 To Line]  on the 
CK-1. 
4- The short modular cord that is attached to [1&2 to Phone] on the CK1 is not used. 

 

Disabling Internal Music-On-Hold on KX-TG4500 

1.  While the base unit is in standby mode, press [MENU]. 
2.  Press DOWN ARROW repeatedly until "

Initial setting

" is Highlighted, press 

[ENTER]. 
3.  Press DOWN ARROW repeatedly until "

Music On Hold

" is Highlighted, press 

[ENTER], then [Enter] again. 
4.  Press DOWN ARROW once, display should read "Off". Press [Enter] to save. 
5. Press [Exit] 

 

Testing the System: 

1- Pickup line 1 on your telephone. The line one LED on the SENSOR BOARD should 
light up. 
 
2- Repeat this test for lines 2-4. If all lines light up when  picked up, the CK-1 is working 
properly. If the lights on the SENSOR BOARD do not light up, then 
  a) Make sure that the CK-1P7 and Phone  is connected to power. 
  b) Make sure that the SENSOR BOARD is flat against the phone. 

Summary of Contents for CK-1P7






Reviews: