background image

#skyviper

#skyviper

www.skyrockettoys.com/products/sky-viper

Customer Service : 

888-674-5650

©2015 Skyrocket Toys LLC, Los Angeles, CA 90066 USA. All Rights Reserved. 

Sky Viper is a registered tradmark and the Skyrocket logo are trademarks of Skyrocket Toys LLC. 

MADE IN CHINA.

t

  Drone may be miscalibrated by launching from an unlevel 

surface.  Turn the remote off and unplug Drone’s battery for 

30 seconds then turn them back on and try again from a 

fl

at, level launching surface.

t

  Ensure your remote is within unobstructed view of Drone and 

you are within 30 feet range.

t

  Ensure the remote has fresh batteries and the LiPo battery 

is fully charged.

t

  Inspect Drone for any possible damage. Turn the remote off 

and unplug Drone’s battery for 30 seconds then turn them 

back on and try again from a 

fl

at, level launching surface.

t

  Drone’s blades may have been installed incorrectly.  Reinstall 

and remember that the Green blades point forward.

t

  Adjust the trim controls until drifting ceases, see page 7.

t

  Propellers may be installed in the wrong position.  Ensure 

proper installation.

t

  Ensure that Drone is 

fl

ying a minimum distance of 9 feet 

from the ground with a minimum 9 feet clearance in all 

directions.

t

  Be sure to detatch the camera unit from the Drone.

Drone is unresponsive or 

behaving erratically 

All blades spin, but Drone 

will not 

fl

y properly

Drone drifts in any 

direction during 

fl

ight 

without direction from the 

remote

Drone crashes 

immediately

Drone crashes when 

attempting stunt functions

Stunt button does not 

work

TROUBLESHOOTING

PROBLEM

SOLUTION

Drone 

fl

ight is erratic when 

Flight Sensitivity is set to 3

t

  Ensure blade guards and camera module are removed to 

reduce performance inhibiting weight.

Summary of Contents for V950STR













Reviews: