IMPORTANT:
YOU ONLY HAVE A FEW
SECONDS AFTER THE LIPO BATTERY IS
PLUGGED IN TO PLACE DRONE ON A
LEVEL SURFACE FOR PROPER CALIBRA-
TION. IF DRONE DOES NOT RISE TO A
STABLE HOVER OR FLIES ERRATICALLY,
REPEAT STEPS 1 THROUGH 6.
CAUTION:
NEVER APPROACH DRONE
WHILE THE PROPELLER BLADES ARE
STILL SPINNING. THROTTLE DOWN UNTIL
THE BLADES STOP THEN TURN OFF
REMOTE BEFORE ATTEMPTING TO
HANDLE DRONE.
FLIGHT SENSITIVITY ADJUSTMENT
CALIBRATING
&
LAUNCHING
1
4
6
Drone responsiveness may be adjusted on the
Controller to match your
fl
ying skills.
There are three choices:
1. BEGINNER – 2. INTERMEDIATE – 3. ADVANCED
It is best to start in
BEGINNER MODE 1
until you
have mastered
fl
ying. Flight sensitivity can be adjusted
before or during
fl
ight.
IMPORTANT:
Advanced Mode 3 is a
performance
fl
ight setting for OUTDOOR USE
ONLY. Blade guards and camera module
MUST BE REMOVED for proper
fl
ight opera-
tion in Mode 3.
1 - BEGINNER
2 - INTERMEDIATE
3 - ADVANCED
1
Turn
OFF
Remote Control.
2
Disconnect the LiPo battery connectors hanging
out from the back of the drone.
Pull connectors, not wires
.
3
Reconnect battery connectors.
4
Quickly place Drone on FLAT LEVEL
SURFACE.
5
Turn Remote Control
ON
.
6
Slowly push remote control THROTTLE
STICK
UP
until Drone lifts into the air.
t
When launching the Drone, face the same direction as the Drone. Green blades should be in front.
t
Practice launching, hovering and landing before attempting to learn other moves.
t
Flying 2 to 3 feet above the ground will reduce ground turbulence and make
fl
ying easier.
t
When
fi
rst attempting to
fl
y in different directions, start by tapping the Direction stick until you have a
feel for it. Always move the controls slowly until you become comfortable operating the drone.
t
Once you’ve mastered
fl
ying in directions, practice Rotational controls. Spinning and keeping Drone
facing the same direction you are facing makes
fl
ying easier and more intuitive.
t
Stay 2 to 3 feet away from walls and ceilings as Drone will be drawn towards them if you
fl
y too
close.
t
If propeller blades come in contact with another object or you crash, throttle down immediately to
prevent possible or further damage.
t
If anything prevents Drone’s blades from spinning or they become jammed,
THROTTLE DOWN
IMMEDIATELY
. Do not attempt to
fl
y until obstruction has been removed and damage
fi
xed.
t
Should something prevent Drone’s blades from spinning, Drone may
AUTO SHUTDOWN
. LiPo
battery will need to be unplugged then reconnected to restore
fl
ying power.
t
If the Drone
fl
ies too far away, beyond the control range of the remote, the Drone will
AUTO-LAND
to prevent the Drone from
fl
ying away out of control.
FLYING TIPS
t
Drone drifts forward
– Press the
B button
t
Drone drifts backward
– Press the
F button
t
Drone drifts to the left
– Press the
R button
t
Drone drifts to the right
– Press the
L button
t
Drone spins counter-clockwise,
when viewed from the top
– Press the
button
t
Drone spins clockwise, when
viewed from the top
– Press the
button
If Drone drifts in any direction while hovering (and you are not pressing the Direction stick),
you may need to make trim adjustments. Safely land Drone on a level surface. Press the
recommended Trim button once as described below. Launch the Drone back into the air and
attempt another still hover. If Drone continues to drift, repeat the process until a still
hover is achieved:
TRIM ADJUSTMENTS
NOTE:
THE REMOTE WILL BEEP/FLASH 3 TIMES WHEN TRIM ADJUSTMENT
IS SET TO THE NEUTRAL POSITION (THE MIDDLE OF THE TRIM RANGE) AND
BEEP ONCE WHEN IT HAS REACHED THE END OF IT’S RANGE.
REMOVING
&
REATTACHING
CAMERA MODULE
The Camera Module is easily removed to improve
fl
ight
performance. Simply unplug the camera connector and slide the
camera module forward to disconnect from drone. To reconnect,
simply clip camera module back onto drone and plug in the wire
connector.
7
4
2
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
PAGE 7 / PAGE 4
3A