background image

 SAFETY PROCEDURES AND NOTES BEFORE SWITCHING ON

IMPORTANT

Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON. 
Be sure to be familiar with the instructions and that you have well understood all 
information contained in this manual. If you have any question contact your 
supervisor or your nearest Dealer.

Danger

An electric cable or electric wire with damaged jacket or bad insulation could 

cause electrical shocks as well as electrical leak. Before use, check conditions of all 
wires and cables.

 Advices

Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood. 
Every function and operational procedure have to be very clear to the operator. 

Contact your nearest Dealer for further questions.

Any manual command (switch, button or lever) shall be given only after being 

sure it is the correct one.

 Precautions

The electric cable has to be compatible with the power required by the machine. 

Cables touching the floor or close to the machine need to be protected against short 
circuits.

AFTER THE WORK ENDS

Cares

Always clean the machine, to do the cleaning  SWITCH IT OFF, AND TAKE 

OUT THE PLUG FROM THE ELECTRICITY SUPPLY SOCKET .

Never clean the machine BEFORE IT IS COMPLETELY STOPED.
Fit all the machine components in their due places, before switching it on 

again.

MAINTENANCE  

Dangers

Any maintenance  is dangerous if made with the machine switched on.
SWITCH IT OFF AND TAKE OUT THE PLUG FROM THE SOCKET, DURING 

ALL THE MAINTENANCE OPERATION.

IMPORTANT 

In any emergency situation, always take the plug out of its socket. 

ADVICES

Electrical or mechanical maintenance shall be made by qualified persons.

The person in charge of the maintenance performances shall check the machine works 
under TOTAL SAFETY CONDITIONS.

05

SKYFOOD EQUIPMENT LLC - SERVICE 

 
For  questions  or  assistance  with  products 

FLEETWOOD  by  SKYMSEN

  and 

SKYMSEN

call  SKYFOOD  EQUIPMENT  Toll  Free

:  1-800-503-7534

,  24h  Customer  support,  or  visit 

the Customer Service section of 

www.skyfood.us

SKYFOOD’S LIMITED WARRANTY 

Unless  otherwise  specified

,

 

new 

FLEETWOOD  by  SKYMSEN

  and 

SKYMSEN 

products, 

excluding accessories, sold by SKYFOOD EQUIPMENT, LLC. (“SKYFOOD”), for use only 
in  the  continental  United  States  (collectively,  “Products”  or  singularly,   “Product”),  are 
warranted  to  be  free  from  defects  in  materials  and  workmanship  for  a  period  of  one  (1) 
year  from  the  date  of  purchase  by  the  original  purchaser/user  (“End  User”).  Several  new 
products  and  accessories  may  be  warranted  for  a  period  other  than  one  (1)  year  while 
others may be subject to travel limitations, as specified on the products Instruction Manual. 

Proof of purchase must be presented; if not this warranty will be VOID.

 No warranty is 

given  or  implied  to  a  subsequent  transferee  or  any  other  third  party.  This  warranty  is 
expressly  conditional  upon  SKYFOOD  being  notified  of  any  defects  in  materials  or 
workmanship  within  five  (5)  days  of  its  occurrence,  within  the  warranted  time  period.  If  a 
notice  of  a  claim  under  this  warranty  is  timely  made  by  the  End  User,  SKYFOOD  or  a 
SKYFOOD’s  designated  service  company  (“Service  Company”),  will  repair  or  replace  the 
Product,  at  SKYFOOD’s  discretion,  subject  to  the  additional  conditions  hereinafter 
described.

 

This  warranty  shall not apply if damage occurs from improper  installation or maintenance 
performed by an unauthorized  service company  (“Service Company”), wrong voltage, nor 
to  the  extent  that  Products  or  parts  have  been  used  other  than  in  conformance  with 
operating  and  maintenance  instructions,  subjected  to  misuse  or  abuse  or  damaged  by 
accident,  acts  of  God,  abnormal  use,  stress or  any  other matter  unrelated  to  SKYFOOD, 
and  beyond  its  reasonable  control. 

This  warranty  does  NOT  cover  service  labor  and 

travel to perform adjustments on products and/or accessories

. In addition to wear and 

tear  of  certain  items,  such  as,  but  not  limited  to;  glass  parts,  blades,  stones,  chopper 
cutting knives, plates, slicing knives, cutting disc, gaskets, oil changes, sealing tape, heat 
seal wires, worm gears, self-lubricating bushings, carbon brushes for electric motors, and 
other  parts  expendable  by  nature  and  that  need  to  be  replaced  frequently. 

Electrical 

components  are  subject  to  natural  wear  and  tear,  and  are  NOT  covered  by  this 
warranty.

 

THIS  WARRANTY  EXCLUDES  ALL  ORAL,  STATUTORY,  EXPRESS  OR 

IMPLIED  WARRANTIES  WHICH  MAY  BE  APPLICABLE  TO  SKYFOOD,  INCLUDING, 
BUT  NOT  LIMITED  TO,  ANY  IMPLIED  WARRANTY  OF  MERCHANTABILITY  AND 
FITNESS  FOR  PARTICULAR  PURPOSE.

  Under  no  circumstances  shall  SKYFOOD  be 

liable  for  loss  of  use,  revenue  or  profit  or  for  incidental  or  consequential  damages. 
SKYFOOD  shall  under  no  circumstances  be  liable  for  any  loss,  damage,  concealed 
damage,  expense or  delay of goods  for  any reason  when  said  goods are  in  the  custody, 
possession  or  control  of  third  parties  selected  by  SKYFOOD  to  forward,  enter,  clear, 
transport,  or  render  other  services  with  respect  to  such  goods.  The  sole  and  exclusive 
remedy  for  breach  of  any  warranty  is  limited  to  the  remedies  provided  in  the  paragraph 
above. 

All  products  held  at  non-commercial  facilities  or  domiciles,  must  be  taken  or  shipped, 
shipping  charges  prepaid,  either  to  SKYFOOD's  facility  or  a  SKYFOOD's  designated 

Summary of Contents for FWD1-33









Reviews: