Front Panel:
1. Gain
：
The gain control adjusts the input sensitivity of the Mic and line inputs on the input channels.
2 High:
allow you to controls the Hi-range of signals 10KHz
（±
12dB
）
3 Mid:
allow you to controls the Mid-range of signals 2.5KHz (
±
12dB)
4 Low
：
allow you to controls the Bass-range of signals 100Hz (
±
12d B)
5 EFF:
use this controls when you want to get effect sound by adjustment of input signal
6 Pan: The Channel Pan positions the output of the channel in the stereo field of the main mix. It’s constant-power
design ensures there are no level discrepancies whether a signal is hard-panned, center-stage, or somewhere in
between.
7 Level:
allow you to adjusts channel signal level to be sent to the master
8 Line:
balanced and unbalanced 1/4 (6.35mm).diameter stereo jack input socket for
connection of high level sound sources.
9 Mic:
electronically balanced XLR connector input socket. For connecting low level signal sources. Such as
microphones or other low impedance devices.
10
MP peak LED: The peak LED illuminates when a amplifier output signal is going into overload. It detects the
peak level on the AMP output and will light at approximately 1dB before clipping to warn that the signal is
approaching overload. You do not want the peak LED to light expect very intermittently during a take or a mix.
If it does light persistently, reduce input gain to protect your speakers.
11 High
：
allow you to controls the Hi-range of the master output signals 10KHz
（±
12dB
）
12 Mid
：
allow you to controls the Mid-range of the master output signals 2.5KHz (
±
12dB)
13 Low
：
allow you to controls the Bass-range of the master output signals 100Hz (
±
12d B)
14 Volume: It allow you to adjust the master output level.
15 Time: It allow you to adjust the delay time of the effect.
16 Depth: This pose allow you to control the echo repeat depth of the effect.
17 EFF Volume: this pose allow you to control the effect level to the master output.
18 Tape: this pose allow you to adjust the level of the tape input to master bus.
19 Send: 1/4 jack connector, output level control by EFF(5)
20 Return: 1/4 jack connector, allowing the output of the remote effect device to be connected to the mixer.
21/22 Tape in: RCA connector, allow you to input high level signal such as TAPE, CD.
23/24 REC output: RCA connector can be used to connect the mixer to the record input of your recorder enabling
you to record your mix.
Rear Panel:
1.
Power switch
：
please make sure that all the volume pose set on the mix position when you want to turn on this
unit, the power LED will be light when you turn on the power switch
2.
Voltage selector
：
before plugging in the power cord, make sure that the voltage selector Switch is set to the
connect voltage.
3.
Power connector with fuse molder.
This standard IEC power cord receptacle is used to connect the AC power to your unit.
4.
Right speaker output
One 1/4 (6.35mm) jacks for you to connecting a speaker cabinet, the min impedance Is 4 ohms
5.
Left speaker output
One 1/4 (6.35mm) jacks for you to connecting a speaker cabinet, the min impedance
Is 4 ohms.
UK
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or
your dealer about the way to proceed.
The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be
changed without prior notice.
WARRANTY CONDITIONS
The date the product leaves the importer is considered to be the date the warranty begins. The law obliges the retailer to offer a
two year quarantee to the enduser.
Only companies approved by Tronios are allowed to work on the equipment.
During warranty period (defective) equipment must be returned to the dealer by pre-paid mail in the original box.
Potentiometers have a limited lifetime and are not covered by the manufacturer for more than normal use.
For all service enquiries, refer to your local distributor, ,as he is best able to help you.
Summary of Contents for 170.297
Page 2: ...Front and Rear Panel ...
